Ice NPS914 Скачать руководство пользователя страница 12

Страница: 12 / 126

Reference: A938

Index: B

Page 12

This document is the property of ICE SAS. It can not be reproduced or communicated to third parties without authorization.

Instruction Manual – NPS914 Alarm and Indication IED

3.4. Control menu

Main menu

The

Control

main menu includes submenus (see the image below) for enabling the various control

functions and objects (

Controls enabled

), enabling and controlling the setting groups (

Setting groups)

configuring the objects (

Objects)

, setting the various control functions (

Control functions)

and configuring

the inputs and outputs (

Device I/O)

. The available control functions depend on the model of the device in

use.

Controls enabled

Figure. 3.4. - 7. Controls enabled submenu.

You can activate the selected control functions in the

Controls enabled

submenu. By default all the control

functions are disabled. All activated functions can be viewed in the

Control functions

submenu (see the

section "Control functions" below for more information).

In this submenu you can also activate and disable the controllable objects. As with control functions, all

Содержание NPS914































































































































Результаты поиска

Содержание NPS914

Отзывы:

Похожие инструкции для NPS914

Бренды по названию

Популярные бренды

Ice NPS914, Инструкция по эксплуатации

Результаты поиска

Содержание NPS914

Отзывы:

Похожие инструкции для NPS914

Бренды по названию

Популярные бренды