background image

User Manual for Models HISU055, HISU075, HISU095

July 2013

Page 8

Connect the power

This is a cord-connected unit, and must be connected 
to its own dedicated power supply. Check the 
dataplate on the back of the machine for the voltage 
and maximum fuse size and per the dataplate use 
fuses or HACR circuit breakers.

Power Cords:

50 Hz models are equipped with a cord without plug. 

When adding a plug, c

onnect the plug to the power 

cord in compliance with the local electrical codes. 

Select an appropriately certified plug based on the 

country of use, current rating of the appliance and 
suitability for use with 1.5 mm 2 x 3 conductor type 
H05VV-F cord

Note: In case the power cord is damaged, it 
must be replaced by a like cord. Replacement 
cords are available from the manufacturer’s local 
representative. Replacement should only be done 

by a qualified technician to prevent possible risks.

The power cord plug will be the disconnect means for 
the machine and must be accessible when the unit is 
in its permanent location.

Follow All Local Codes - This Unit Must Be 
Grounded. 
Do not use extension cords and do not 
disable or by-pass ground prong on electrical plug.

Plug the power cord into the power supply.

Installation check list

• 

Has the machine been installed indoors in an 

environment suitable for it?

• 

Have all of the shipping items and packaging been 

removed?

• 

Is the ice chute in the correct position?

• 

Is the clear plastic curtain hanging down and free to 

move?

• 

Has the water supply been connected and 

confirmed to not leak?

• 

Has a properly sized and sloped drain tube been 

attached?

• 

Has the correct voltage power supply been 

connected?

Front view of freezing compartment, right arrow points 
to clear plastic curtain. It must hang freely. Left arrow 

points to cube deflector, it must be positioned as 

shown.

Front view of freezing compartment, shown without 
Ice Chute. Left arrow points to Spray Platform, located 

under cube deflector. Spray Platform inlet connects 

to pump hose and is snapped into clip at back of 
reservoir.

Spray 
Platform

Drain Plug

Содержание HISU055


















Отзывы: