manualshive.com logo in svg

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию

Поделиться
Скачать
ICE AIR ccHPWH Series Скачать руководство пользователя страница 24

21 

 

VI. Electrical wiring diagram 

1.  Notice 

•

 

The power supply voltage must conform to the rated voltage

. 

•

 

Wiring must be carried out by a professional and wired in accordance with wiring diagram

. 

•

 

Ensure the power supply wires are properly sized and protected from excessive current (please refer 

to the performance specification and parameters table for details)

. 

•

 

Units shall be grounded and wired per national wiring electrical code. 

 

•

 

The power and ground wires must be tightened by applying the right torque with the right tools.

 

•

 

Only  the  electrical  components  specified  by  the  company  can  be  used,  and  the  installation  and 

technical services are required from the designated manufacturer or authorized dealer. If the wiring is 

not in accordance with the electrical installation specifications, it may lead to the failure of the controller 

or electric shock

. 

•

 

According  to  the  national  technical  standards  for  electrical  equipment,  set  up  leakage  protection 

devices

. 

•

 

After all the wiring is completed, the power can be connected only after careful inspection

. 

•

 

Please read the labels on the electrical cabinet

. 

•

 

The power supply wire for outdoor installation of the unit shall not be lower gauge than the neoprene 

armored flexible cord (line 57 in IEC 60245), and the wire diameter specification of the power supply 

wire shall be selected according to the rated maximum current of the nameplate, as shown in the table 

below

：

 

 

Maximum current (A) 

 

Area of wire (

mm²)  Switch nominal specification( A) 

≤16 

≥2.5 

25 A 

≤25 

≥4 

32 A 

≤32 

≥6 

40 A 

≤41 

≥6 

50A 

≤57 

≥10 

63 A 

≤76 

≥16 

80 A 

≤101 

≥25 

100 A 

≤125 

≥35 

125 A 

≤135 

≥50 

160A 

 

•

 

When  the  power  supply  is  connected,  it  must  be  equipped  with  a  full-pole  disconnection  device 

matching with the unit and at least 0.12 inches contact distance from the power supply and a leakage 

protection device

. 

•

 

If the supply cord is damaged, it must be replaced by a professional in the designated manufacturer's 

maintenance department or similar department to avoid danger

. 

•

 

The power supply shall be housed in a weather tight enclosure, 60 inches or more above the ground. It 

is forbidden to be installed in a moist, acidic, corrosive environment or exposed to direct sunlight

. 

Содержание ccHPWH Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды