manualshive.com logo in svg

ICC OPC-PRT3, Инструкция по эксплуатации, Страница: 3 / 115

Поделиться
Скачать
ICC OPC-PRT3 Скачать руководство пользователя страница 3

ICC 

 

2 

Preface 

This instruction manual has been prepared to help you connect your FRENIC-MEGA, FRENIC-HVAC, 
FRENIC-HVAC-P, FRENIC-AQUA, or FRENIC-Ace inverter to Industrial Ethernet networks using the 
OPC-PRT3 Multiprotocol Ethernet interface card. This instruction manual does not contain inverter 
usage instructions. Please refer to this instruction manual in conjunction with the applicable inverter 
instruction manual in order to become familiar with the proper handling, installation and operation of this 
product. Improper handling or installation procedures may result in incorrect operation or premature 
product failure. 
 

Related Publications 

Listed below are publications that are necessary for reference in conjunction with this instruction manual 
and are subject to change without notice. Please be sure to refer to the most recent available versions. 

•

 

RS-485 User's Manual (24A7-E-0082) 

•

 

FRENIC-MEGA Instruction Manual (INR-SI47-1457-E) 

•

 

FRENIC-M

EGA User’s Manual (MEHT536) 

•

 

FRENIC-HVAC Instruction Manual (INR-S147-1610-E) 

•

 

FRENIC-

HVAC User’s Manual (24A7-E-0069) 

•

 

FRENIC-HVAC-P Addendum (FEA-ACDR-IN-123) 

•

 

FRENIC-AQUA Instruction Manual (INR-S147-1611-E) 

•

 

FRENIC-

AQUA User’s Manual (24A7-E-0077) 

•

 

FRENIC-Ace Instruction Manual (INR-SI47-1733a-E) 

•

 

FRENIC-Ace 

User’s Manual (24A7-E-0043E) 

 

Safety precautions 

Please read this instruction manual thoroughly prior to proceeding with installation, connections, 
operation, or maintenance and inspection. Additionally, ensure that all aspects of the system are fully 
understood, and familiarize yourself with all safety information and precautions before operating the 
inverter. 
 
Safety precautions in this instruction manual are classified into the following two categories: 
 

 

Failure to heed the information indicated by this symbol may lead 
to dangerous conditions, possibly resulting in death or serious 
bodily injuries. 

 

Failure to heed the information indicated by this symbol may lead 
to dangerous conditions, possibly resulting in minor or light bodily 
injuries and/or substantial property damage. 

 
Failure to heed the information contained under the CAUTION title can also result in serious 
consequences. These safety precautions are of utmost importance and must be observed at all times. 
 

Security information 

ICC provides products and solutions that support the operation of plants, systems, machines and 
networks.  In order to protect these critical assets against cyber threats, it is necessary to implement and 
continuously maintain a holistic, state-of-the-

art industrial security concept. ICC’s products and solutions 

comprise only one element of such a concept. 
 
Customers are solely responsible for preventing unauthorized access to their plants, systems, machines 
and networks.  Systems, machines and components should be connected to the enterprise network or 
the internet only if appropriate security measures (such as the use of firewalls and network 
segmentation) are employed to the extent necessary. 
 
ICC’s products and solutions undergo continuous development to make them more secure.  ICC 
strongly recommends the application of product updates as soon as they are available.  The use of 
product versions that are no longer supported, and the failure to apply the latest available updates may 
increase the customer’s exposure to cyber threats. 

Содержание OPC-PRT3




















































































































Отзывы:

Нет отзывов