ICC Mirius Скачать руководство пользователя

Страница: 23 / 56

BACnet / Electric Water Heaters

BACNET / ELECTRIC WATER HEATERS

Figure 35. Custom and Gold Xi™ Series Electric Water Heaters (Virtual BACnet device via ICC Gateway)

PRODUCT DESCRIPTION

The Mirius is a multiprotocol RS-485 to RS-485 gateway. The ETH-1000 is an Ethernet to RS-485 multiprotocol gateway. These

products supports native BACnet, connecting directly to IP or the MS/TP LAN using baud rates of 4800, 9600, 19200, 38400, 57600,

76800, and 115200. As shipped the devices are configured as a BACnet Server.
All electronic controls provide communications via propriety protocol with the ICC Gateway. The Mirius supports BACnet MS/TP

communications and the ETH-1000 supports BACnet IP to access data available at the display plus control of a limited number of

points such as Operating Setpoint.

PROTOCOL IMPLEMENTATION CONFORMANCE STATEMENT (PICS)

BACnet Standardized Device Profile (Annex L):

BACnet Application Specific Controller (B-ASC)

BACnet Interoperability

Table 15. BACnet Interoperability Building Blocks Supported (Annex K):

Data Sharing - ReadProperty-A (DS-RP-A)



Data Sharing - ReadProperty-B (DS-RP-B)



Data Sharing - ReadPropertyMultiple-B (DS-RPM-B)



Data Sharing - WriteProperty-A (DS-WP-A)



Data Sharing - WriteProperty-B (DS-WP-B)



Data Sharing - WritePropertyMultiple-B (DS-WPM-B)



Data Sharing – COV-B (DS-COV-B) (BACnet/IP only)



Device Management-Dynamic Device Binding-A (DM-DDB-A)



Device Management-Dynamic Device Binding-B (DM-DDB-B)



Device Management-Dynamic Object Binding-B (DM-DOB-B)



Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды