ICC Mirius Скачать руководство пользователя страница 20

Страница: 20 / 56

BACnet / Gas Water Heaters

Table 10. BACnet/Gas Water Heaters Object List

BACnet

Object Name

(Description)

BACnet

Object

Type/Inst.

BACnet

Object

Property

R/W

Units

Min

Value

(if W)

Max

Value

(if W)

Xi 1.0

Mxi

Blower Relay

(Blower Relay output commanded status)

Binary Output 402

Present_Value

0 = Off

1 = On



Ignition Relay

(Ignition Relay output commanded status)

Binary Output 403

Present_Value

0 = Off

1 = On



Gas Valve Relay

(Gas valve Relay output commanded status)

Binary Output 404

Present_Value

0 = Off

1 = On



MXi Ign Tries

(Selects 1 or 3 tries for ignition. Settable at UIM)

Binary Value 501

Present_Value

0 = 3 tries

1 = 1 try



MXi Use Ext Enab

(Selects whether or not to use Optional External

Enable Input. Settable at UIM)

Binary Value 502

Present_Value

0 = No

1 = Yes



MXi Modulation

(CCB S/W version 3.15 or higher. Disables mod

ulation on heaters that have it. May be helpful if

plumbed with Xi 1.0. Settable at UIM)

Binary Value 503

Present_Value

0=Disabled

1=Enabled



System In Fault

Binary Value 504

Present_Value

0 = Okay

1 = Alarm



System State

(CCB Control State)

Multistate Value 801

Present_Value

See Table 10



Fault Code

Multistate Value 802

Present_Value

See Table 13



Alert Code

Multistate Value 803

Present_Value

See Table 13



1. Data is encoded into the 16 bits as major revision (upper 8 bits) and minor revision (lower 8 bits).

2. Not recommended for use currently as UIM does not currently support and warning will come up as “Unknown.”

Central Control Board Major State Definitions

Table 11.

Gas Central Control Board (CCB) Major State Definitions

Value

Xi 1.0 State

MXi State

Off (Standby)

Pre-Purge

Igniter Warmup

Igniting

Ignition Activation

Gas Valve On

Ignition Verification

Inter-Purge

Heating

Post-Purge

In Fault

Fault

Xi 1.0 Energy Management System (EMS) Control

Xi 1.0 uses a single bit setting method. Within the EMS Mode-Status point one bit command (bit 15) sets it in EMS mode, and other

ends EMS mode. Once in EMS mode, another bit command (bit 0) enables heating another disables heating.
Once in EMS mode the EMS Mode Refresh command must be periodically issued which clears a third bit (bit 14) to maintain EMS

mode, otherwise the heater will end EMS mode and resume normal operation.

Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды