IC Medical HD 450 Скачать руководство пользователя страница 58

Страница: 58 / 62

Chapter 10

– Malfunctions

Malfunction messages

Code

Malfunction/warning

Possible causes

Recommended course of action

201

Power failure

A running program was interrupted by
a power failure

Check the circuit breakers

Program must be restarted
Disinfection cannot be confirmed

Do not turn off the unit at the power
switch when a program is running.

202

Doors were opened

Door was opened during the cleaning
and disinfection process

Cleaning and disinfection process
was not completed!

Close the doors and restart the
program

203

No fresh water supply

Water mains turned off,

screen of supply hose clogged

Supply hose pinched when setting up

Turn on the mains

Inspect the screen of the supply hose

Check the supply hose along its
length

204

Lye pump is blocked

Outlet hose pinched, outlet valve or
hose clogged

Foreign object in the lye pump

Inspect runoff hose for bends
or pinches

205

No processing media found No processing media was inserted

Insert Thermo Tab

Program must be restarted

206

Injection pump

Injection filter clogged

Remove filter and inspect

Insert a new filter

207

Conductivity too high

The water quality in the previous wash
cycle was too low

Processing media did not dissolve
completely

Remove any remaining processing
media from the unit

Restart program

208

Washing arm is not turning Washing arm is blocked by washware

Wash nozzles clogged

Rearrange washware, clear clog

Clean washing arm

Содержание HD 450































































Результаты поиска

Содержание HD 450

Отзывы:

IC Medical HD 450, Руководство пользователя, Страница: 58 / 62

Результаты поиска

Содержание HD 450

Отзывы: