IBM TotalStorage SAN256N Director 2045-N16 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 157

IBM TotalStorage SAN256N Director 2045-N16 Скачать руководство пользователя страница 69

Chapter 3. Installation

49

Note: If you purchased an Eneterprise Manager workstation from IBM, the software will

be installed on the PC. Refer to the IBM TotalStorage SAN n-type Director Family
Enterprise Manager Installation and Operator Guide (GC26-7720) for more
information.

Installing and setting up Enterprise Manager 9.x on an existing FC/9000
platform

This section describes the steps to upgrade an existing Enterprise Manager workstation
from Enterprise Manager version 8.3.x to version 9.x to allow operation of the SAN256N
director within the FC/9000 fabric.

Note: Enterprise Manager versions earlier than 8.3.x are not supported.

The primary requirements for SAN256N director and FC/9000 operation are:

• Enterprise Manager version 9.x

• SAN256N director system operating version 1.x firmware

• FC/9000 system operating version 5.x firmware

Install Java Runtime Environment (JRE) Software

Use this procedure to install the Java Runtime Software.

Note: IBM recommends that previous versions of Java and Java Webstart are

uninstalled prior to the installation of the Java Software.

1. Insert the Enterprise Manager version 9.x CD into the CD drive of the workstation.

Open Windows Explorer and select the CD drive.

2. Run j2re1-4-2-04-windows-i586-p.exe from the Enterprise Manager CD to install

the Java software. Click Yes on the ConfigSave screen to save the existing
configuration. Java creates a file of the current configuration.

3. Run the Java installation wizard and accept all default settings. After the program

loads, click Finish to exit the installation wizard. Perform a restart of the workstation
to complete the Java installation.

Installing Enterprise Manager 9.x software

Use this procedure to install version 9.x of the Enterprise Manager.

1. Run Setup.exe from the Enterprise Manager CD.

2. Click Yes to the configuration snapshot question.

3. Click Next at the Enterprise Manager installation startup screen.

4. Select I Agree, then click Next on the License Agreement screen.

5. Click Next to accept English on the Local Language screen.

6. Accept the default directory for the Enterprise Manager installation, click Next.

Note: In an Enterprise Manager upgrade installation, all configuration database files

are already established in this directory path. IBM does not recommend selecting
a new directory path with existing database files.

7. Click Next on the Enterprise Manager Installation Location screen to start the

installation.

«
...
67
68
69
70
71
...
»

Содержание TotalStorage SAN256N Director 2045-N16






























































































































































Отзывы:

Нет отзывов