IBM totalstorage 326 Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 240

background image

Appendix E. Setup procedures and diagnostics for the Fibre
Channel Hub

This appendix provides setup and diagnostic information for the IBM 3534 Fibre
Channel Hub, Model 1RU.

Note:

Throughout this section, the term

switch

refers to switches and hubs unless

otherwise noted.

General information

The hub is designed for maintenance-free operation. When there is a suspected
failure, the hub has self-diagnostic capabilities to aid in isolating any equipment or
fabric failures.

The hub supports power-on self-tests (POSTs) and diagnostic tests. The diagnostic
tests determine the status of the hub and isolate problems.

Telnet commands are used to determine the status of the hub, error conditions, and
hub operating statistics. A Telnet session can be established from the IBM
StorWatch SAN Fibre Channel Managed Hub Specialist. The same Telnet
commands can also be issued using the service terminal connected to the serial
port.

Attention:

Many of the diagnostic tests are disruptive to hub operation. Read the

information on each diagnostic before beginning a test or procedure.

Isolating a system fault

Various loopback paths are built into the hub hardware for diagnostic purposes. A
loopback path test within the hub verifies the proper internal Fibre Channel port
logic functions and the paths between the interfaces and central memory.

Diagnostics also supports external loops that include the system board and the
GBIC module in cross-port configurations. These port-to-port diagnostics allow you
to check installed fiber cables and perform port fault isolation.

Removing power

After all data transferring processes external to the hub are completed, removing
power from the hub does not disrupt the fabric.

Note:

Error messages are stored in random access memory (RAM) and are lost
when power is removed from the hub. Access the error message log to view,
and note any error messages before removing power from the hub.

Service actions for error messages

See “Error messages” on page 165 for error message descriptions and the
appropriate service actions.

Setting up partnering with the 3534 Fibre-managed hubs

The following steps allow you to re-partner the 3534 Fibre-managed hubs.

Note:

Partnering of the hubs is set up on the product before it is shipped to you.

© Copyright IBM Corp. 2002

155

«
...
165
166
167
168
169
...
»

Содержание totalstorage 326

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для totalstorage 326

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: Palm Страницы: 4

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

Бренд: H3C Страницы: 116

Бренд: National Instruments Страницы: 9

Бренд: Netopia Страницы: 38

Бренд: Konig Страницы: 73

3C410012A - OfficeConnect Remote 531 Access...

Бренд: 3Com Страницы: 72

Бренд: Freescale Semiconductor Страницы: 921

Бренд: SUNRICH TECHNOLOGY Страницы: 5

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Roland Страницы: 2

Бренд: Realtek Страницы: 30

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды