IBM System Storage TS2230 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 141

background image

5.

After viewing all error codes, exit this function by pressing the Unload Button

again. The SCD will display

0

and exit Maintenance Mode.

Function Code A: Clear Error Code Log

Function Code

A

erases the contents of the error code log.

1.

Place the drive in Maintenance Mode. For instructions, see “Entering
Maintenance Mode” on page 3-8.

2.

Press the Unload Button once per second until

A

appears in the SCD. (If you

cycle past the desired code, press the Unload Button once per second until the
code reappears.)

3.

Press and hold the Unload Button for three or more seconds, then release it to

select the function.

A

flashes in the SCD, followed by

0

. The tape drive

erases all errors from the error code log and exits Maintenance Mode.

Function Code C: Insert Cartridge into Tape Drive

This function cannot be selected by itself, but is part of other maintenance
functions (such as Run Tape Drive Diagnostics and Create FMR Tape) that require
a tape cartridge to be inserted.

Function Code E: Test Cartridge & Media

Approximate Run Time = 15 minutes per loop

Total Number of Loops = 10

Function Code

E

performs tests that determine whether a suspect cartridge and

its magnetic tape are acceptable.

Press the Unload Button to stop the diagnostic and exit maintenance mode.
Pressing the Unload Button once will abort the test at the end of the current test
loop. Pressing the Unload Button twice will abort the test immediately. Wait for the
drive to rewind the tape and unload the cartridge.

Attention:

When you perform this test, data on the suspect tape will be

overwritten.

Note:

If you inserted an invalid tape cartridge (e.g. FMR or WORM media), error

code

J

or

7

appears in the SCD. If you inserted a write-protected

cartridge, or the media has read-only compatibility (e.g., Gen1 media), error

code

P

appears in the SCD. In either case, the tape drive unloads the

cartridge and exits Maintenance Mode after the cartridge is removed.

1.

Place the drive in Maintenance Mode. For instructions, see “Entering
Maintenance Mode” on page 3-8.

3-16

TS2230 Tape Drive Setup, Operator and Service manual

«
...
52
53
54
55
56
...
»

Содержание System Storage TS2230














































































































































Отзывы:

Нет отзывов

Похожие инструкции для System Storage TS2230

Бренд: LaCie Страницы: 2

Бренд: Seville Classics Страницы: 9

Aspire EASYSTORE H341

Бренд: Acer Страницы: 59

Aspire EASYSTORE H341

Бренд: Acer Страницы: 74

Aspire EasyStore Series

Бренд: Acer Страницы: 148

Aspire easyStore H340

Бренд: Acer Страницы: 68

Altos EasyStore

Бренд: Acer Страницы: 169

Aspire easyStore H340

Бренд: Acer Страницы: 148

Altos EasyStore

Бренд: Acer Страницы: 7

Бренд: TyeDee Bin Страницы: 2

Бренд: G-Technology Страницы: 24

Pro 2-Disk RAID USB and eSATA

Бренд: Verbatim Страницы: 56

Бренд: Echostreams Страницы: 3

GV-Storage System

Бренд: GeoVision Страницы: 9

Бренд: Promise Technology Страницы: 38

Бренд: brennenstuhl Страницы: 40

Бренд: StarTech.com Страницы: 8

mini usb 2.0 companion hard drive

Бренд: LaCie Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды