IBM SureMark 4610 1NF страница 52 Скачать руководство пользователя

Страница: 52 / 112

Removing the electronic journal slot card

The fiscal logic card does not have to be removed from the tray to remove the electronic journal slot card
from its mount on the logic card.

To remove the electronic journal slot card, complete the following steps:

1. Remove the fiscal tray from the printer.

2. Remove the screws that secure the cover; then, remove the cover from the tray by lifting it straight up

and off the tray. The fiscal memory is epoxied to the inside of the cover and also connects to the fiscal
logic card preventing the cover from being easily removed.

3. Press out on the two rentention tabs

on the electronic journal slot assembly

and lift the edge of

the card

(Figure 14); then, rotate the card up and out of the mounting bracket.

Installing the electronic journal slot

This section provides information needed for installing the entire electronic journal slot assembly and the
electronic journal slot card.

Figure 14. Remove the electronic journal slot card

Removing and replacing FRUs

SureMark Hardware Service

Содержание SureMark 4610 1NF

















































































































Результаты поиска

Содержание SureMark 4610 1NF

Отзывы:

Похожие инструкции для SureMark 4610 1NF

Бренды по названию

Популярные бренды

IBM SureMark 4610 1NF, Руководство по обслуживанию оборудования

Результаты поиска

Содержание SureMark 4610 1NF

Отзывы:

Похожие инструкции для SureMark 4610 1NF

Бренды по названию

Популярные бренды