IBM SureMark 4610 1NF страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 112

background image

Removing the fiscal logic card

This section provides the information needed to remove the fiscal logic card from a fiscal tray provided by
IBM. If your fiscal solution is provided by an IBM business partner, see the documentation provided by the
IBM business partner for more information. The fiscal logic card is the logic card installed in the fiscal logic
tray and should not be confused with the logic card that is installed on the printer unit under the main
cover.

Note:

It is not necessary to remove the program memory from the logic card to complete the steps. It is
necessary to remove the screw that secures the program memory.

To remove the fiscal logic card, complete the following steps:

1. Place the fiscal tray on a clean, flat, static-protective surface.

2. Remove the electronic journal card from the card slot and set it aside for future use.

Removing and replacing FRUs

Chapter 5. Removing and replacing FRUs

31

«
...
43
44
45
46
47
...
»

Содержание SureMark 4610 1NF

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SureMark 4610 1NF

I-Class Mark II

Бренд: Datamax Страницы: 12

Бренд: Panasonic Страницы: 2

Бренд: JCM Страницы: 70

Бренд: Partex Страницы: 16

Бренд: Xerox Страницы: 6

Бренд: Lexmark Страницы: 6

Бренд: SPRT Страницы: 14

BIZHUB 8050 CF5001

Бренд: Konica Minolta Страницы: 20

Бренд: Skynet Страницы: 18

DPR-1260 - RangeBooster G Multifunction Print Server

Бренд: D-Link Страницы: 55

Бренд: D-Link Страницы: 49

V105 - All-in-One Printer

Бренд: Dell Страницы: 68

P703w - Photo All-in-One Printer Color Inkjet

Бренд: Dell Страницы: 105

Бренд: Dell Страницы: 125

Бренд: Dell Страницы: 108

Бренд: Dell Страницы: 612

Photo All-in-One 966

Бренд: Dell Страницы: 135

P513w All In One Photo Printer

Бренд: Dell Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды