![background image](http://html1.mh-extra.com/html/ibm/san64b-6/san64b-6_installation-service-and-user-manual_3515865100.webp)
6 CORE BLADE 176 CR32-4 ENABLED
7 SW BLADE 178 FC32-48 ENABLED
8 AP BLADE 186 SX6 ENABLED
4. Verify that the device is functioning correctly by entering
switchShow
or
switchStatusShow
.
This
switchShow
command displays the device and port status information.
switch0:admin> switchshow
switchName: sw0
switchType: 165.0
switchState: Online
switchMode: Native
switchRole: Principal
switchDomain: 130
switchId: fffc82
switchWwn: 10:00:00:05:31:03:2c:00
zoning: ON (ZONE_CONFIG_NAME)
switchBeacon: OFF
FC Router: OFF
HIF Mode: OFF
Allow XISL Use: OFF
LS Attributes: [FID: 128, Base Switch: No, Default Switch: Yes,
Address Mode 0]
Index Slot Port Address Media Speed State Proto
=======================================================
64 4 0 014000 -- N32 Online FC F-Port 10:00:00:05:1e:f8:a0:b4
65 4 1 014100 -- N32 Online FC F-Port 10:00:00:05:33:26:0e:65
66 4 2 014200 -- N32 Online FC F-Port 10:00:00:05:33:48:5e:f5
67 4 3 014300 -- N32 Online FC F-Port 10:00:00:05:1e:f8:a0:b3
68 4 4 014400 -- N32 Online FC F-Port 10:00:00:05:1e:f8:a0:b6
(output truncated)
5. Verify that all the IP address information is correct by entering
ipAddrShow
and checking the results
against the IP information recorded in the config-miscinfo.txt file.
switch:admin> ipaddrshow
SWITCH
Ethernet IP Address: xxx.xxx.xxx.12
Ethernet Subnetmask: 255.55.0.0
Fibre Channel IP Address: 1.2.3.4
Fibre Channel Subnetmask: 255.255.255.0
CP0
Ethernet IP Address: xxx.xxx.xxx.10
Ethernet Subnetmask: 255.55.0.0
HostName : cp0
Gateway Address: xxx.xxx.xxx.1
CP1
Ethernet IP Address: xxx.xxx.xxx.11
Ethernet Subnetmask: 255.55.0.0
HostName : cp1
Gateway Address: .1
Backplane IP address of CP0 : 10.0.0.4
Backplane IP address of CP1 : 10.0.0.5
switch:admin>switch:admin>
Verifying correct configuration of the fabric
About this task
Copying the command outputs from this section into a file is recommended. You must be logged in with
Admin privileges.
Procedure
1. Create an "after" SAN profile by entering the following commands and copying the output to a text file
named SANafter.txt:
76 IBM Storage Networking SAN64B-6: SAN64B-6 Installation, Service, and User Guide
Содержание SAN64B-6
