manualshive.com logo in svg

IBM RackSwitch G8332, Руководство по установке, Страница: 44 / 86

Поделиться
Скачать
IBM RackSwitch G8332 Скачать руководство пользователя страница 44

Air duct mounting bracket

M6 screws

M3.5 screws

5. Use the M3.5 screws to secure the air duct mounting bracket to the rack

chassis. Torque the screws to approximately 1.1 Nm +/- 0.1 Nm (10
inch-pounds).

6. Gently slide the air duct unit side flanges into the card guides until the unit is

seated firmly. Make sure that the foam strip is oriented on top.

M4

thumbscrews

Side flanges

Card guides

Foam

7. Use the two M4 thumbscrews to secure the air duct unit to the air duct brackets.

For information about removing the air duct, see “Removing the 1U air duct option”
on page 41.

Installing a QSFP+ transceiver

The RackSwitch G8332 supports QSFP+ fiber transceivers. For the available
transceivers for the switch, see https://www-01.ibm.com/products/hardware/
configurator/americas/bhui/launchNI.wss.

The QSFP+ ports accept approved QSFP+ transceivers. The QSFP+ optical
transceiver provides an MTP cable connector for connecting to external ports.

28

IBM System Networking RackSwitch G8332: Installation Guide

Содержание RackSwitch G8332























































































Отзывы:

Нет отзывов