IBM Power Systems Series Скачать руководство пользователя страница 30

Страница: 30 / 134

Table 6. Storage device problems and service actions (continued)
Problem

Service action

System unable to find a storage device

1. If the system was recently installed, moved,

serviced, or upgraded, verify that the device is

seated and installed properly.

2. Verify that the device is compatible with your

system.

3. Verify that all internal cables are properly

seated and are not physically damaged.

4. Verify that the most recent firmware is installed

on the system, or install the most recent

firmware if it is not already installed.

5. If the device is part of a RAID configuration,

ensure that the device has been enabled and is

part of an array.

6. Install the device in an open or free slot. If the

device is able to be found replace the

component with the failing connector.

7. Replace the storage device.
8. Replace any applicable attached cable.

More than one storage device suddenly stops

working

1. If the system was recently installed, moved,

serviced, or upgraded, verify that the device is

seated and installed properly.

2. Check the system logs to verify whether the

system detected a problem.

3. Replace the cable that connects the disk drive

backplane to the system backplane.

One storage device suddenly stops working

1. Verify that all internal cables are properly

seated and are not physically damaged.

2. Check the system logs to verify whether the

system detected a problem.

3. Replace the drive.
4. Replace the system backplane.
5. Replace the cable.

Содержание Power Systems Series







































































































































Результаты поиска

Содержание Power Systems Series

Отзывы:

Бренды по названию

Популярные бренды

IBM Power Systems Series, Анализ проблем, составные части системы и расположение

Результаты поиска

Содержание Power Systems Series

Отзывы:

Бренды по названию

Популярные бренды