IBM Power System 5148-22L Скачать руководство пользователя | Manualshive

Страница: 198 / 204

background image

Electromagnetic Interference (EMI) Statement - Russia

Class B Notices

The following Class B statements apply to features designated as electromagnetic compatibility (EMC)
Class B in the feature installation information.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

v

Reorient or relocate the receiving antenna.

v

Increase the separation between the equipment and receiver.

v

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

v

Consult an IBM-authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible for
any radio or television interference caused by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Industry Canada Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

European Community Compliance Statement

This product is in conformity with the protection requirements of EU Council Directive 2014/30/EU on
the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot
accept responsibility for any failure to satisfy the protection requirements resulting from a
non-recommended modification of the product, including the fitting of non-IBM option cards.

180

Disk drives or solid-state drives

«
...
196
197
198
199
200
...
»

Содержание Power System 5148-22L













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power System 5148-22L

Бренд: TANDBERG Страницы: 276

e Server iSeries 825

Бренд: IBM Страницы: 52

Бренд: Galleon Страницы: 47

UniServer T1100 G3

Бренд: H3C Страницы: 138

Бренд: Xblue Networks Страницы: 42

Бренд: AIC Страницы: 79

Бренд: t.a.c. Страницы: 36

Ultra Enterprise 3000

Бренд: Sun Microsystems Страницы: 48

PRIMERGY CX120 S1

Бренд: Fujitsu Страницы: 82

PRIMERGY BX922 S2

Бренд: Fujitsu Страницы: 106

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 290

PRIMERGY BX924 S4

Бренд: Fujitsu Страницы: 286

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 64

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 51

SMARTSERVER 370

Бренд: Samsung Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды