IBM P260 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 524

background image

Installing a DIMM

The very low profile (VLP) dual-inline memory module (DIMM) is a tier 1 CRU. You can install it
yourself. If IBM installs a tier 1 CRU at your request, you will be charged for the installation. The low
profile (LP) DIMM is a tier 2 CRU. You can install it yourself or request IBM to install it, at no additional
charge, under the type of warranty service that is designated for the compute node.

About this task

To install a DIMM, complete the following steps:

Procedure

1.

Read the Safety topic and the “Installation guidelines” on page 35.

2.

Read the documentation that comes with the DIMMs.

3.

Shut down the operating system on all partitions of the compute node, turn off the compute node,
and remove the compute node from the IBM Flex System Enterprise Chassis. See “Removing the
compute node from an IBM Flex System Enterprise Chassis” on page 37.

4.

Carefully lay the compute node on a flat, static-protective surface, with the cover side up.

5.

Open and remove the compute node cover. See “Removing the compute node cover” on page 39.

6.

Locate the DIMM connectors on the system board. Determine the connector into which you will
install the DIMM. See “Supported DIMMs” on page 59.

7.

Touch the static-protective package that contains the part to any unpainted metal surface on the IBM
Flex System Enterprise Chassis or any unpainted metal surface on any other grounded rack
component, and then remove the new part from its shipment package.

8.

Verify that both of the connector retaining clips are in the fully open position.

9.

Turn the DIMM so that the DIMM keys align correctly with the connector on the system board.
Attention:

To avoid breaking the DIMM retaining clips or damaging the DIMM connectors, handle

the clips gently.

10.

Insert the DIMM (B) by pressing the DIMM along the guides into the connector.

Verify that each retaining clip (A) snaps into the closed position.

Figure 26. Installing a DIMM

58

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
68
69
70
71
72
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

Бренд: NEC Страницы: 26

Бренд: Walgreens Страницы: 41

Бренд: Garmin Страницы: 6

Бренд: Elo TouchSystems Страницы: 37

Бренд: Wells-Gardner Страницы: 25

Бренд: Mace Страницы: 2

Laser LT RD-1550

Бренд: C&S Controls Страницы: 44

Бренд: Anslut Страницы: 6

Бренд: Tandy Страницы: 45

YUR.VISION YV19WP2

Бренд: YURAKU Страницы: 2

Бренд: Beurer medical Страницы: 120

Бренд: Luvion Страницы: 58

Бренд: Welch Allyn Страницы: 28

Бренд: FDS Страницы: 14

Бренд: FDS Страницы: 16

Бренд: ipf electronic Страницы: 25

SyncMaster 2033SN

Бренд: Samsung Страницы: 20

SyncMaster 216BW

Бренд: Samsung Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды