IBM P260 Скачать руководство пользователя страница 519 | Manualshive

Страница: 519 / 524

background image

Electromagnetic Interference (EMI) Statement - Russia

Class B Notices

The following Class B statements apply to features designated as electromagnetic compatibility (EMC)
Class B in the feature installation information.

Federal Communications Commission (FCC) statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

v

Reorient or relocate the receiving antenna.

v

Increase the separation between the equipment and receiver.

v

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

v

Consult an IBM-authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible for
any radio or television interference caused by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Appendix. Notices

507

«
...
517
518
519
520
521
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Бренд: Samsung Страницы: 28

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Бренд: Samsung Страницы: 29

SyncMaster C27A750X

Бренд: Samsung Страницы: 102

Бренд: Raymarine Страницы: 390

Бренд: Garmin Страницы: 3

Бренд: Acer Страницы: 3

Бренд: Acer Страницы: 5

Бренд: Acer Страницы: 3

Бренд: Acer Страницы: 22

Бренд: Acer Страницы: 28

Бренд: Acer Страницы: 35

Бренд: Acer Страницы: 21

Бренд: Samsung Страницы: 41

Бренд: A&D Страницы: 27

Бренд: VARIZOOM Страницы: 2

Бренд: AG Neovo Страницы: 33

Бренд: Avtek Страницы: 15

Бренд: Unicont SPb Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды