IBM Netfinity ServeRAID-3H Скачать руководство пользователя страница 22

Страница: 22 / 212

Adapter Features

Standard features of the ServeRAID-3H and ServeRAID-3L adapters
are as follows.

Feature

ServeRAID-3H

ServeRAID-3L

Arrays (max.)

Array Accelerator

Yes

Battery Backup

Yes (Optional)

Cache Memory

32 MB

4 MB

Hard Disk Drives (max.)

Hot-Spare Drives (max.)

Logical Drives (max.)

Microprocessor

40 MHz

25 MHz

SCSI Channels

SCSI Transfer Speed (max.)

80 MB /sec.

Supported RAID Levels

0, 1, 5, and
Enhanced-1

0, 1, 5 and
Enhanced-1

System PCI Data Bus

64 bit

32 bit

Connector Locations

This section provides illustrations of the channel connectors, cable
connectors, and optional devices for the ServeRAID-3H and
ServeRAID-3L adapters.

The light-emitting diodes (LEDs) on the adapters indicate activity on
the SCSI channels and provide diagnostic information for trained
service technicians.

IBM ServeRAID-3H and ServeRAID-3L Adapters

Содержание Netfinity ServeRAID-3H





















































































































































































































Результаты поиска

Содержание Netfinity ServeRAID-3H

Отзывы:

IBM Netfinity ServeRAID-3H, Инструкция по установке и эксплуатации, Страница: 22 / 212

Результаты поиска

Содержание Netfinity ServeRAID-3H

Отзывы: