IBM Netfinity ServeRAID-3H Скачать руководство пользователя страница 132

Страница: 132 / 212

On - The adapter or controller
chooses the recovery method when
there is a ServeRAID startup error.

Code Block Version

The current version number of the
firmware loaded on the adapter or
controller.

Boot Block Version

The current version number of the
bootable microcode loaded on the
adapter or controller.

Concurrent Commands

The maximum number of
concurrent commands supported.

Maximum Devices Supported

The maximum number of devices
supported.

Flash Program Count

The current number of times the
flash EEPROM has been written.

Defunct Disk Count

The current number of defunct hard
disk drives.

Rebuild Rate

The current setting (Low, Medium,
or High) of the rebuild rate.

Hot-Swap Rebuild

The current state (Enabled or
Disabled) of the hot-swap rebuild
feature.

Offline Logical Drive Count

The current number of offline
logical drives.

Configuration Update Count

The number of times that the
ServeRAID configuration has been
updated.

NVRAM Battery Backup Device The current state of the

battery-backup cache (installed, not
installed, or defective).

122

IBM ServeRAID-3H and ServeRAID-3L Adapters

Содержание Netfinity ServeRAID-3H





















































































































































































































Результаты поиска

Содержание Netfinity ServeRAID-3H

Отзывы:

IBM Netfinity ServeRAID-3H, Инструкция по установке и эксплуатации, Страница: 132 / 212

Результаты поиска

Содержание Netfinity ServeRAID-3H

Отзывы: