IBM Medium J11 Скачать руководство пользователя

Страница: 58 / 104

26. Install the shipping screws (optional step required only for preventing non-operating transportation

shock/vibration)

The figure above identifies an installed shipping screw using a red arrow. A shipping screw installs

above each of the crossbar thumbscrews as shown in the enclosure rear panel view included above

this step.
Note: After the enclosure is secured in the rack, install the disks.

Routing cables using the CMA

About this task
Routing of power and data cables for the JBOD is integral to successful rail kit installation and rackmount

installation of the enclosure. Cables must be correctly installed and routed to facilitate efficient operation

and in-rack servicing of the enclosure.
This procedure describes the routing of cables through the CMA, including using the CMA baskets and the

CMA storage shelf located at the rear of the enclosure.

Procedure

1. Install the data cables and route them through the CMA brackets.

a) Rotate the CMA cable capture arms so they are out of the way of the data cable routing.

b) Route data cables 1–5 onto the CMA shelf and through the CMA brackets in the order and

configuration shown below.

c) Secure the routed cables with one hand, while installing additional cables until data cables 1–5 are

installed.

d) Rotate the outer cable capture arm close over data cables 1–5, ensuring it seats in the C-flange in

between the two cable capture arms.

Note: This model of the Disk Enclosure does not contain an IOM in slot 1. Thus, disregard the red

cables in the figures below.

38 IBM Cloud Object Storage System: Medium/Large J11/J12 Disk Enclosure Hardware Installation and

Maintenance Manual

Содержание Medium J11









































































































Результаты поиска

Содержание Medium J11

Отзывы:

Похожие инструкции для Medium J11

Бренды по названию

Популярные бренды

IBM Medium J11, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Medium J11

Отзывы:

Похожие инструкции для Medium J11

Бренды по названию

Популярные бренды