IBM Medium J11 Скачать руководство пользователя

Страница: 42 / 104

Table 11. LED - Dual path LFF disk drive carrier modules - top panel
State (Amber)

Status

Off

Normal

Short blink (1 sec)

Identify

Fault - A fault has been detected or a service action

is required.

Long blink (3 secs)

Rebuild

The replacement procedure should be completed within an absolute maximum of 3 minutes. For

additional information about LFF disk LED behavior, see the “Disk drive carrier module LED” on page 48

section.

Controller channel fan module
The controller channel fan module supplements the system fans by circulating airflow within the

enclosure controller channel, and providing cooling for the IOMs. The replacement procedure should be

completed within an absolute maximum of three minutes.

Figure 20. LEDs: Controller channel fan module - top panel

22 IBM Cloud Object Storage System: Medium/Large J11/J12 Disk Enclosure Hardware Installation and

Maintenance Manual

Содержание Medium J11









































































































Результаты поиска

Содержание Medium J11

Отзывы:

Похожие инструкции для Medium J11

Бренды по названию

Популярные бренды

IBM Medium J11, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Medium J11

Отзывы:

Похожие инструкции для Medium J11

Бренды по названию

Популярные бренды