IBM M791 Series Скачать руководство пользователя страница 29

Страница: 29 / 38

PCI / Plug and Play Setup Page

This page sets some of the parameters for devices installed on the
PCI bus and devices that use the system plug and play capability.

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

Plug and Play Aware O/S Yes
Share Memory Size

32MB

Primary Graphics Adapter PCI
Allocate IRQ to PCI VGA Yes
PCI IDE BusMaster

Disabled

ESC : Quit

↑↓←→

: Select Item

F1    :  Help             PU/PD/+/- : Modify
F5    :  Old Values   (Shift)F2    : Color
F6   :  Load BIOS Defaults
F7   :  Load Setup Defaults

Plug and Play

Aware O/S

Enable this item if you are using an O/S that
supports Plug and Play such as Windows 95
or 98.

Share Memory

Size

This item lets you allocate a portion of the
main memory for the onboard VGA display
application with 8/16/32MB options.

Primary Graphics

Adapter

This item indicates if the primary graphics
adapter uses the PCI or the AGP bus. The
default PCI setting still lets the onboard
display work and allows the use of a second
display card installed in a PCI slot.

Allocate IRQ to

PCI VGA

If this item is enabled, an IRQ will be
assigned to the PCI VGA graphics system.
You set this value to No to free up an IRQ.

PCI IDE BusMaster

This item enables or disables the DMA under
DOS mode. We recommend you to leave this
item at the default value.

Содержание M791 Series







































Результаты поиска

Содержание M791 Series

Отзывы:

Похожие инструкции для M791 Series

Бренды по названию

Популярные бренды

IBM M791 Series, Руководство пользователя

Результаты поиска

Содержание M791 Series

Отзывы:

Похожие инструкции для M791 Series

Бренды по названию

Популярные бренды