IBM Infoprint 1130 Скачать руководство пользователя | Manualshive

Страница: 51 / 433

background image

2-24

Service Manual

IBM Infoprint 1130/1140

User Status Screens

User Status Screens

Status

Action

Ready

Ready
<Fax Status>

The printer is ready to
receive and process
data

or

The printer will display
the FAX status.

Press Menu> or
<Menu to take the
printer out of Ready
and enter all the
Menus except the
TESTS MENU (Busy
State).

Ready/Hex

The printer is ready and
HEX Trace is active,
which is known as HEX
Trace Ready.

Press Menu> or
Menu< to take the
printer out of Ready
and enter the TESTS
MENU (Busy State).
Press Select for the
values. Press Menu>
until Reset Printer is
on the second line of
the display. Press
Select to Reset the
printer.

Power Saver

Power Saver
<Fax Status>

When in the power
saver mode, the printer
will display this screen
instead of the Ready
screen. When a job is
received, the power
saver screen remains
displayed until the
printer exits the power
saver mode and warms
up the printer.

The printer has been
configured to receive or
send FAX. This screen
is displayed.

Press Menu > or
Menu< to take the
printer offline and
access the Ready
Menu Group.

or

Press GO to take the
printer out of power
saver and initiate a
printer warm up cycle.

or

Press Stop to take the
printer offline. The Not
Ready message is
displayed, no more
data is processed.
The Go button must
be pressed to return
the printer to the
previous state.

«
...
49
50
51
52
53
...
»

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infoprint 1130

Бренд: Oki Страницы: 33

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 11

Бренд: OKIDATA Страницы: 58

Бренд: UltraTape Страницы: 52

Бренд: Ultimaker Страницы: 101

Бренд: Panasonic Страницы: 166

imageRUNNER ADVANCE DX 6870i

Бренд: Canon Страницы: 115

imagerunner advance C5550i

Бренд: Canon Страницы: 1556

Бренд: QuickLabel Systems Страницы: 122

Бренд: Lexmark Страницы: 9

Бренд: ABLE Страницы: 42

Бренд: Geeetech Страницы: 52

Бренд: Oce Страницы: 186

Бренд: idp Страницы: 48

Бренд: SII Страницы: 85

Бренд: M&R Страницы: 36

Бренд: MIMAKI Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды