manualshive.com logo in svg

IBM Infoprint 1130, Руководство по обслуживанию

Поделиться
Скачать
IBM Infoprint 1130 Скачать руководство пользователя страница 195

3-30

Service Manual

IBM Infoprint 1130/1140

screen by pressing the Go button. Once the Quick Test Page 
completes printing, the Registration screen displays again.

Note:  The Quick Test Page should be printed on A4 or Letter 
paper only.

5. To exit the Registration menu, press Return. 

Printer Setup

Setting the Page Count 

This lets the servicer change the page count from the diagnostic 
menu. This is used whenever the system board is replaced because 
this board contains the printer NVRAM Memory where the page 
count is stored.

To set the Page Count:

1. Select Page Count from the Diagnostic menu.

– The current page count displays.

– The leftmost digit blinks, indicating it is the first digit to be 

changed.

2. Press either Menu until the value you want displays.

3. Press Select to move to the next digit, press Menu until the 

value you want displays. Continue with each digit until you set 
the page count. You can skip any digit by pressing Select.

4. Press Select to save the new page count in NVRAM.

5. Press Return/Stop to exit the Diagnostic menu.

Viewing the Permanent Page Count

The Permanent Page Count can only be viewed and cannot be 
changed.

To view the Permanent Page Count:

1. Select Permanent Page Count from the menu.

2. Press Return/Stop to exit the Diagnostic menu.

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды