background image

 

Chapter 4.  Operating the storage server

 35

RAID controller cache battery

Each RAID controller contains a sealed, rechargeable 4-volt lead-acid battery. This 
battery provides cache backup for up to three days in the event of a power loss.

The service life of the battery is three years, after which time the battery must be 
replaced. Refer to the storage-management software for information on how to view 
and set the battery expiration date.

Each RAID controller has a green Battery LED on the back that indicates the battery 
status, as follows: 

• The LED is on and remains steady when the battery is fully charged.

• The LED flashes when the battery is charging or performing a self-test.

• The LED is off if the battery or the battery charger has failed.

The battery performs a self-test at startup and every 25 hours thereafter (during which 
time the Battery LED flashes). If necessary, the battery begins recharging at that time. 
If the battery fails the self-test, the Battery LED turns off, indicating a battery fault.

Data caching starts after the battery completes the startup tests.

The following illustration shows the location of the Battery LED on the front of the 
RAID controller.

Battery LED

Содержание FAStT200 HA



















































































































Отзывы: