IBM DCS3860 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 204

background image

Enclosure ID Settings

The enclosure ID is a unique two-digit identifier for each enclosure in the storage
system configuration. In a dual controller or ESM configuration, both enclosure IDs
are identical under normal operating conditions. Each DCS3860 storage system and
EXP3800 expansion enclosure in the storage system configuration must have a
unique storage enclosure ID.

The controller automatically sets the enclosure ID. You can change the setting
through the DS Storage Manager software, if necessary. The range of supported
enclosure ID settings is 0 through 99. The enclosure ID is normally set to a value of
00 at the factory.

The enclosure ID is displayed on the seven-segment numeric display located on
the back of each controller and ESM.

Working with SAS cables

Use a 1M or 3M (1-meter or 3-meter) SAS cable with a mini-SAS 4x multilane SAS
connector at each end. Use this cable to connect a controller host port to a host
HBA and the drive expansion port to a storage enclosure.

The following illustration shows the 1M and 3M mini-SAS cable.

The 1M and 3M SAS cables have a universal key connector that enables the cable
to be used in all mini-SAS ports.

Mini-SAS
connectors

Figure 17. Mini-SAS cable

44

IBM System Storage DCS3860 Storage System: Installation, User's, and Maintenance Guide

«
...
60
61
62
63
64
...
»

Содержание DCS3860













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCS3860

Бренд: G-Technology Страницы: 32

Бренд: G-Technology Страницы: 35

Бренд: WATSON Страницы: 12

Бренд: Backyard Discovery Страницы: 72

GLADIATOR PLUS 2

Бренд: Asgard Страницы: 6

StorNext QD7000

Бренд: Quantum Страницы: 29

Бренд: Facom Страницы: 2

Бренд: Seagate Страницы: 20

Бренд: INTILION Страницы: 121

BAULE EVO 80 BAULE EVO 120

Бренд: garofalo Страницы: 16

2GB - 2GB Micro Secure Digital Card

Бренд: SanDisk Страницы: 26

Бренд: Western Digital Страницы: 2

Бренд: Thunderbolt Страницы: 37

Бренд: LOOQS Страницы: 69

Бренд: D-Link Страницы: 69

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 170

Flexline CompactContainer

Бренд: Oka Страницы: 12

Бренд: Acomdata Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды