IBM CS821 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 118

background image

To turn the drive light on:

sas3ircu <controller_#> locate <Enclosure:Bay> ON

And off:

sas3ircu <controller_#> locate <Enclosure:Bay> OFF

To view additional help for the command:

sas3ircu help

NVMe commands

Learn about the NVMe commands. These commands are for NVMe drives together with feature code
EKAE using an NVMe PCIe adapter.

If the

nvme

command is not installed, download the utility from https://github.com/linux-nvme/nvme-

cli. Follow the installation instructions found on that site.

To determine which drive you want to replace, use the command:

nvme list

If you are searching for a failed drive, you can check each drive using the command:

nvme smart-log <device>

To turn on the identify LED, use the command:

dd if=/dev/nvmeX of=/dev/null

You can also use the

ledctl

command from the optional

ledmon

package:

ledctl locate=/dev/rsnvmeX

To get the device serial number for verification, use the command:

nvme id-ctrl /dev/nvmeX | grep -i sn

To take the device offline so that it can be removed:

sh -c"echo 0 >/sys/block/nvmeX/device/delete"

Sensor readings GUI display

The sensor readings GUI display is a way to quickly determine the general health status of the server
without having to look at the detailed system event log (SEL) information.

To view the sensor readings GUI display, log in to the BMC web interface. Click Server Health > Sensor
Readings

.

Some occurrences of errors in the system might not appear in the sensor readings GUI. After you view
the sensor readings GUI display, use the SEL logs to view any active SEL events that indicate a service
action event.

Sensor readings display operation

Most sensors are initially gray, then change status and color during the boot process when the FRU is
initialized and either determined to be good (green) or faulty (red). No sensor display is available until
you can get to the sensor display selection on the BMC, which means that the system attains a certain
power level or that the BMC finishes initializing. The indicator color of the sensor is determined based on
the sensor status at time of invocation of the display. The sensor display maintains the sensor status
indicator color until the display is refreshed, which updates the sensor value with the latest status.

Common procedures for servicing or installing features in the 8001-12C or 8005-12N

77

«
...
91
92
93
94
95
...
»

Содержание CS821























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS821

Бренд: Rapid Страницы: 6

Бренд: TREND Страницы: 32

Akku-Press 22 V ACC

Бренд: REMS Страницы: 212

EdgePower EP-24V-72W

Бренд: Ubiquiti Страницы: 16

Бренд: Unimac Страницы: 15

Бренд: Yamato Страницы: 12

Бренд: Yamato Страницы: 14

Бренд: Fein Страницы: 189

Бренд: Rehau Страницы: 36

Бренд: P.I.T. Страницы: 24

Бренд: Yokota Страницы: 8

Бренд: APS Страницы: 156

KH 3050 ELECTRIC NAILER

Бренд: Parkside Страницы: 52

Бренд: Jet Страницы: 16

Бренд: YATO Страницы: 2

Бренд: Skil Страницы: 12

Бренд: Devine Страницы: 5

Бренд: SRC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды