IBM CS821 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 118

background image

What to do next

If you press the power button and the system does not start, contact your next level of support or your
service provider.

Stopping the 8001-12C, 8001-22C, 8005-12N, or 8005-22N system

Learn how to stop the IBM Power System S821LC (8001-12C), the IBM Power System S822LC for Big
Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) systems to complete another
task.

Procedure

You can use the Linux

shutdown

command to stop and power down the system.

For example, the following command will shut down the system in 10 minutes and send the message
“Repairs coming” to the users.

shutdown -P +10 "Repairs coming"

The

-P

setting instructs the system to shut down and then power down. The

+

indicates the time in

minutes before the shutdown occurs.

Drive commands for 8001-12C, 8001-22C, 8005-12N, or 8005-22N

Learn about the storage drive commands for the IBM Power System S821LC (8001-12C), the IBM Power
System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) systems.

mvCLI commands

Learn about the mvCLI commands. They are for SATA drives and drive on modules (DOMs) that are
directly connected to the system backplane without using a PCIe adapter.

To enter the

mvCLI

commands, enter this command to enable the commands:

Figure 79. Power switch for 8001-22C

74

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
88
89
90
91
92
...
»

Содержание CS821























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS821

Бренд: Wacker Neuson Страницы: 156

Бренд: Keithley Страницы: 160

Бренд: Keithley Страницы: 22

Бренд: Keithley Страницы: 66

Бренд: Keithley Страницы: 58

Бренд: W&T Electronics Страницы: 24

Бренд: Emcore Страницы: 13

HSP-176M-1500-HD

Бренд: Baileigh Industrial Страницы: 44

Бренд: Westfalia Страницы: 18

Бренд: Malibu Boats Страницы: 4

Бренд: Fein Страницы: 113

Бренд: Panduit Страницы: 2

Бренд: Xantrex Страницы: 76

Бренд: Parkside Страницы: 98

Бренд: Far Tools Страницы: 25

Бренд: Malibu Boats Страницы: 2

Бренд: Altronix Страницы: 2

Бренд: Kaidi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды