IBM BladeCenter HS22V 7871 страница 194 Скачать руководство пользователя | Manualshive

Страница: 194 / 258

background image

ServerGuide problems

Use this information to locate ServerGuide problems and suggested actions.

The following table lists problem symptoms and suggested solutions.

Symptom

Suggested action

The

ServerGuide Setup and

Installation

CD will not start.

v

Make sure that the CD drive is associated with the blade server that you are
configuring.

v

Make sure that the blade server supports the ServerGuide program and has a
bootable CD (or DVD) drive.

v

If the startup (boot) sequence settings have been changed, make sure that the
CD drive is first in the startup sequence.

The RAID configuration
program cannot view all
installed drives, or the
operating system cannot be
installed.

v

Make sure that there are no duplicate SCSI/SAS IDs or interrupt request (IRQ)
assignments. See “Configuring a RAID array” on page 35.

v

Make sure that the storage drive is connected correctly. See “Blade server
connectors” on page 14 to locate the storage drive connector.

The operating-system
installation program
continuously loops.

Make more space available on the hard disk.

The ServerGuide program will
not start the operating-system
CD.

Make sure that the operating-system CD is supported by the ServerGuide
program. See the

ServerGuide Setup and Installation

CD label for a list of supported

operating-system versions.

The operating system cannot be
installed; the option is not
available.

Make sure that the operating system is supported on the blade server. If the
operating system is supported, either no logical drive is defined (SCSI/SAS RAID
systems) or the ServerGuide System Partition is not present. Run the ServerGuide
program and make sure that setup is complete.

Software problems

Use this information to diagnose and resolve software problems for the blade
server.

Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.

178

BladeCenter HS22V Type 7871 and 1949: Problem Determination and Service Guide

«
...
192
193
194
195
196
...
»

Содержание BladeCenter HS22V 7871



































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HS22V 7871

Бренд: Lanner Страницы: 43

UniServer R4900 G5

Бренд: H3C Страницы: 141

TJA670 domovea Basic

Бренд: hager Страницы: 36

Бренд: MSI Страницы: 106

Бренд: Intermec Страницы: 232

Бренд: Kyocera Страницы: 207

SuperServer 2028R-C1R(T)4+

Бренд: Supermicro Страницы: 1

Бренд: ZLAN Страницы: 13

PRIMERGY TX2540 M1

Бренд: Fujitsu Страницы: 92

PRIMERGY TX200 S5

Бренд: Fujitsu Страницы: 114

PRIMERGY TX300 S5

Бренд: Fujitsu Страницы: 142

PRIMERGY TX200 S6

Бренд: Fujitsu Страницы: 126

Server PRIMERGY TX1330 M1

Бренд: Fujitsu Страницы: 336

PRIMERGY TX300 S6

Бренд: Fujitsu Страницы: 122

Бренд: Fujitsu Страницы: 86

Бренд: Fujitsu Страницы: 109

PRIMERGY TX200 S5

Бренд: Fujitsu Страницы: 110

PRIMERGY TX300 S5

Бренд: Fujitsu Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды