Configuring
remote
access
After
you
connect
the
active
management
module
to
the
network,
the
Ethernet-port
connection
is
configured
in
one
of
the
following
ways:
v
If
you
have
an
accessible,
active,
and
configured
DHCP
server
on
the
network,
the
host
name,
IP
address,
gateway
address,
subnet
mask,
and
Dynamic
Name
Server
(DNS)
server
IP
address
are
set
automatically.
v
If
the
DHCP
server
does
not
respond
within
3
minutes
after
the
port
is
connected
to
the
network,
the
management
module
uses
the
factory-defined
static
IP
address
and
default
subnet
address.
The
management
module
is
inaccessible
during
this
time.
To
configure
remote
access,
complete
the
following
steps:
1.
Make
sure
that
the
client
computer
is
on
the
same
subnet
as
the
management
module;
then,
use
a
Web
browser
to
connect
it
to
the
management
module.
2.
In
the
browser
Address
field,
specify
the
IP
address
that
the
management
module
is
using:
v
If
the
IP
address
was
assigned
through
a
DHCP
server,
get
the
IP
address
from
your
network
administrator.
v
The
factory-defined
static
IP
address
is
192.168.70.125,
the
default
subnet
address
is
255.255.255.0,
and
the
default
host
name
is
MM
xxxxxxxxxxxx
,
where
xxxxxxxxx
is
the
burned-in
media
access
control
(MAC)
address.
The
MAC
address
is
on
a
label
on
the
management
module,
below
the
reset
button.
Note:
If
the
IP
configuration
is
assigned
by
the
DHCP
server,
the
network
administrator
can
use
the
MAC
address
of
the
management-module
network
interface
to
determine
which
IP
address
and
host
name
are
assigned.
See
your
management-module
User’s
Guide
for
instructions
for
configuring
the
management
module.
Communicating
with
the
IBM
Director
software
The
IBM
®
Director
program
communicates
with
the
BladeCenter
unit
through
the
Ethernet
port
on
the
active
management
module.
To
communicate
with
the
BladeCenter
unit,
the
IBM
Director
software
needs
a
managed
object
(in
the
Group
Contents
pane
of
the
IBM
Director
Management
Console
main
window)
that
represents
the
BladeCenter
unit.
If
the
management-module
IP
address
is
known,
the
network
administrator
can
create
an
IBM
Director
managed
object
for
the
unit.
If
the
IP
address
is
not
26
BladeCenter
Advanced
Management
Module:
Installation
Guide
Содержание BladeCenter Advanced Management Module
