c.
Once you locate your expansion unit, look at the
Logical Address
field.
The value for X is the second digit in the field.
Example:
The following is an example of how to find the Direct Select Address for
location D41. The Direct Select Address from Table 4 on page 41 for
location D41 is 0X10 0007 00FF. The value for X is under the
LOGICAL ADDRESS
field in the System Configuration List as shown in the
example below:
LOGICAL ADDRESS
1/4/ /-/ / / / /
Under the
LOGICAL ADDRESS
field, the second digit is
4
. Therefore the
Direct Select Address for location D02 in this example is 0410 0007 00FF.
__ 4.
Record the Direct Select Address for your disk unit to use in the concurrent
install procedure.
Performing the concurrent install
Follow these steps to perform the concurrent install:
Attention:
Failure to follow these instructions could result in damage to the
removable media device or the system-unit and could result in loss of data.
__ 1.
If you have not already, sign on as
QSECOFR
__ 2.
On the AS/400 command line, type:
STRSST
Press the Enter key.
__ 3.
When the System Service Tools display appears, select the Start a service
tool option. Press the Enter key.
__ 4.
When the Start a Service Tool display appears, select the Hardware service
manager option. Press the Enter key.
__ 5.
When the Hardware Service Manager display appears, select the Device
Concurrent Maintenance option.
__ 6.
You can install the removable media device in one of three possible
positions. Refer to label on the inside of the front cover to locate the direct
select address of the position you will be installing the removable media.
__ 7.
Type the
Direct Select Address
of the position where you will be installing
the removable media device.
__ 8.
Pull out the removable media filler bezel.
__ 9.
Remove the long plastic connector cover.
__ 10.
Attention:
Removable media devices are fragile. Handle with care.
Be sure to use the wrist strap provided.
Place one end of the wrist strap
around your wrist and connect the opposite end to your expansion unit.
__ 11.
Find the package that contains the new removable media assembly and
remove it from the static-protective package.
__ 12.
Hold the device with the blue button in the upper right for tape units or
lower right for CDs.
Note:
Support the bottom of the removable media device as you install it into the
expansion unit. Do not hold the removable media device by the blue handle.
__ 13.
Pull the blue handle out toward you before you install the disk unit into
the expansion unit.
Appendix D. Installing removable media devices in the 5065 Expansion Unit
59
Содержание AS/400e
