IBM AS/400e Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 85

background image

Appendix D. Installing removable media devices in the 5065
Expansion Unit

You may install removable media device features into the 5065 or 5066 Expansion
Unit yourself. It takes approximately 1 hour to install the hardware. However, if
you elect not to install the feature, contact IBM or an authorized dealer to install
the removable media device feature for a fee.

Allow additional time to complete your jobs, to back up your system, and to IPL
your system, and verify your hardware configuration.

When you use these instructions, you will do the following:

v

Remove the front cover for the expansion unit.

v

Install your new hardware.

v

Install the cover.

v

IPL your operating system.

v

Verify your new hardware configuration.

Note:

Your 5066 Expansion Unit consists of two independent 5065 Expansion
Units. The installation instructions for each expansion unit in your 5066 are
identical.

Before you begin:

v

Ensure that you have a current backup of your operating system and licensed
programs. If you have backed up the operating system and licensed programs
since the last time you applied PTFs, that backup is acceptable.

v

Ensure that you take a few minutes to become familiar with these instructions.

v

If there are incorrect, missing, or visibly damaged parts, contact one of the
following:
– Your authorized dealer
– IBM Rochester Manufacturing Automated Information Line (R-MAIL)

- 1-800-300-8751 (United States)
- 1-507-253-5242 (worldwide)

Table 5. Possible removable media device configurations

Removable Media Device

Possible Installation Configurations
(double for 5066)

CD-ROM Drive (4425)

One per 5065

4 GB Tape Drive (4482)

Install up to 2

12 GB Tape Drive (4483)

Install up to 2

25 GB Tape Drive (4486)

Install up to 2

© Copyright IBM Corp. 1999, 2000

55

«
...
65
66
67
68
69
...
»

Содержание AS/400e






















































































Отзывы:

Нет отзывов

Похожие инструкции для AS/400e

DataTraveler Locker+ Generation 3 DTLPG3

Бренд: Kingston Technology Страницы: 1623

Бренд: SanDisk Страницы: 4

Бренд: TrekStor Страницы: 100

Бренд: Tennsco Страницы: 4

Бренд: Dancover Страницы: 12

Бренд: Newpo Страницы: 5

CANOPIA RUBICON

Бренд: Palram Страницы: 71

Do It Yourself Workbench EI-PT1013

Бренд: Excalibur Страницы: 2

Бренд: SonicWALL Страницы: 56

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 4

Бренд: Craftsman Страницы: 13

Бренд: Craftsman Страницы: 6

Бренд: Craftsman Страницы: 3

Бренд: Craftsman Страницы: 4

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды