IBM Aptiva 2170 Скачать руководство пользователя страница 177

Страница: 177 / 252

143

Software Recovery Procedure

The Recovery CD includes an install program that can be used to restore the
original system software.

To recover the original software on the hard disk drive, use the following
procedures:

1. Insert the Aptiva recovery CD into the CD-ROM drive then restart computer.

2. Depress F1 while POST to enter BIOS Setup menu. Select and enter

“Startup Options”, set the first priority of boot sequence to CD-ROM. Save
and exit from BIOS Setup.

3. After system boots from recovery CD, you will be prompted with an “IBM

Product Recovery Program” menu, follow the instructions on the screen to
operate the software recovery procedure.

Содержание Aptiva 2170





























































































































































































































































Результаты поиска

Содержание Aptiva 2170

Отзывы:

IBM Aptiva 2170, Руководство по обслуживанию оборудования, Страница: 177 / 252

Результаты поиска

Содержание Aptiva 2170

Отзывы: