manualshive.com logo in svg

IBM 9080-M9S, Руководство пользователя

IBM 9080-M9S - Профессиональный сервер высочайшего класса, обеспечивающий надежное и эффективное функционирование вашего бизнеса. Подробное руководство по эксплуатации доступно для бесплатного скачивания на manualshive.com. Получите свой Manual прямо сейчас и ознакомьтесь с возможностями этого выдающегося устройства.

Поделиться
Скачать
background image

7. When the service processor comes up to the Flexible Service Processor (FSP) standby state (the

power-on LED on the control panel is flashing slowly), continue to the next step.

8. Access the ASMI and run the Cable Plugging Validation utility to validate all of the cables.

a) If you are already connected to the ASMI, go to the next step. Otherwise, click All Systems then

select system being serviced.  Then, click Actions > View All Actions > Launch Advanced

Systems Management (ASM).

b) In the navigation area, expand System Service Aids > Cable Plugging Validation. Then, click

Validate Cables. The system verifies that the expected cables are present.

c) If your configuration includes two or more nodes, expand System Service Aids > Cable Plugging

Validation. Then, click Verify Node Position. Otherwise, if your configuration includes only one

node, continue to the next step.
If the system is cabled correctly, the blue identify LED on each system node will light up, in

sequence, from the top node to the bottom node. If the LEDs do not light up in sequence, the FSP

cables need to be re-installed.

d) Expand System Service Aids > Cable Plugging Validation. Then, select All of the above in the

Display Cable Status section and click Continue. The system validates that the cables are

installed in the correct locations. Expand System Service Aids > Cable Plugging Validation to

display a table with the results. Ensure that the plugging status is OK for each cable in the

displayed table. If the status is OK, no further action is required. If the status is not OK, review the

error logs, correct the problems, and repeat steps b, c and d as needed until the status is OK for

all cables.

e) Exit the ASMI.

9. If you replaced a PCIe3 x8 non-volatile memory SSD NVMe adapter and the logical partition that

controls the adapter is running the IBM i operating system, complete the following steps to prepare

the NVMe adapter for operation:

a) Start the IBM i System Service Tools (STRSST), and specify the user name and password.

b) On the System Service Tools (SST) display, select Work with disk units > Work with disk

configuration > Work with NVM Devices > Delete existing NVM Namespaces.

c) Select the device that you replaced.

d) Choose from the following options:

• If no namespaces are listed, press F12 to return to the SST main menu and continue with the

next step.

• If there are namespaces listed, complete the following steps:

1) Select 4=Delete Namespace for each of the listed namespaces.
2) Press F10 to confirm the deletion of the namespaces.
3) Press F12 to return to the SST main menu.

e) On the System Service Tools (SST) display, select Work with disk units > Work with disk

configuration > Work with NVM Devices > Create NVM Namespaces to pair with Active mirror

protected NVM units.

f) Select the NVMe device that you replaced.

g) On the Create NVM Namespaces - Show the Units Suspended from Mirror Protection display,

press F7 to select all of the suspended disk units.

h) Press F10 to confirm the creation of the listed namespaces that will be paired with the suspended

disk units.
Note: The operation will create new namespaces on the selected NVMe device, pair the new

namespaces with the suspended NVMe disk units, and start to resume mirror protection on the

newly created disk units.

i) Press F12 to return to the SST main menu.

PCIe adapters  479

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9080-M9S

Park Tool CRC-1 Manual preview
CRC-1
Бренд: Park Tool Страницы: 2
XPOtool 51808 Operating Manual preview
51808
Бренд: XPOtool Страницы: 10
Levolta iX05 black edition User Manual preview
iX05 black edition
Бренд: Levolta Страницы: 14
REDSTONE RS 80E SS Original Instructions Manual preview
RS 80E SS
Бренд: REDSTONE Страницы: 70
PEUGEOT EnergyGrind-100 Using Manual preview
EnergyGrind-100
Бренд: PEUGEOT Страницы: 10
Ingersoll-Rand IQV20 W7002 Series User Manual preview
IQV20 W7002 Series
Бренд: Ingersoll-Rand Страницы: 56
Malibu Boats ML200RT Instructions preview
ML200RT
Бренд: Malibu Boats Страницы: 2
Parkside PAS 4 C4 Translation Of The Original Instructions preview
PAS 4 C4
Бренд: Parkside Страницы: 107
BorMann HOME BFC3000 Owner'S Manual preview
HOME BFC3000
Бренд: BorMann Страницы: 4
Gude 02823 Translation Of The Original Instructions preview
02823
Бренд: Gude Страницы: 44
Scheppach 5908207901 Original Instruction Manual preview
5908207901
Бренд: Scheppach Страницы: 192
West Industries LaserLine Instruction Manual preview
LaserLine
Бренд: West Industries Страницы: 13
Hamach Buggy 10 User Manual preview
Buggy 10
Бренд: Hamach Страницы: 24
Elektro-Automatik 21 540 122 User Manual preview
21 540 122
Бренд: Elektro-Automatik Страницы: 28
Panduit BT2HT Operation Instructions preview
BT2HT
Бренд: Panduit Страницы: 4
Rapid DUAX Operator'S Manual preview
DUAX
Бренд: Rapid Страницы: 20
Milwaukee M12 CH User Manual preview
M12 CH
Бренд: Milwaukee Страницы: 28
Extron electronics EPS 1210 P Specification Sheet preview
EPS 1210 P
Бренд: Extron electronics Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды