IBM 9006-12C Скачать руководство пользователя страница 98

Страница: 98 / 126

What to do next

If you press the power button and the system does not start, contact your next level of support or your
service provider.

Stopping the 9006-12C or 9006-22C system

Learn how to stop the IBM Power System LC921 (9006-12C) or IBM Power System LC922 (9006-22C)
systems to complete another task.

Procedure

You can use the Linux

shutdown

command to stop and power down the system.

For example, the following command will shut down the system in 10 minutes and send the message
“Repairs coming” to the users.

shutdown -P +10 "Repairs coming"

The

-P

setting instructs the system to shut down and then power down. The

indicates the time in

minutes before the shutdown occurs.

Drive commands for 9006-12C or 9006-22C

Learn about the storage drive commands for the IBM Power System LC921 (9006-12C) or IBM Power
System LC922 (9006-22C) systems.

arcconf commands

Learn about the

arcconf

commands. They are for SATA drives and drive on modules (DOMs) that are

directly connected to the system backplane without using a PCIe adapter.

To list the logical drives and device configurations. For additional information about the

arcconf

tool,

refer to http://i.adaptec.com/power

Figure 86. Power switch for 9006-22C

Power Systems: Servicing the IBM Power System LC921 (9006-12C)

Содержание 9006-12C































































































































Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды

IBM 9006-12C, Руководство пользователя

Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды