IBM 7378 Скачать руководство пользователя страница 310

Страница: 310 / 362

Removing a heat-sink retention module

Alignment
triangle

To remove a heat-sink retention module, complete the following steps:

1. Read the safety information that begins on page vii and “Handling

static-sensitive devices” on page 151.

2. Turn off the server and all attached devices; then, disconnect all power cords

and external cables.

3. Carefully turn the server on its side so that it is lying flat, with the cover facing

up.

Attention:

Do not allow the server to fall over.

4. Unlock and remove the left-side cover (see “Removing the left-side cover” on

page 181).

5. Remove the power supply or power supplies from the power-supply cage (see

“Removing a hot-swap power supply” on page 273).

6. Rotate the power-supply cage to its open position (see “Opening the

power-supply cage” on page 154).

7. Remove the air baffle (see “Removing the air baffle” on page 212).

8. Remove the heat sink (see “Removing a microprocessor and heat sink” on

page 284).

9. Using a Phillips screwdriver, remove the four screws that secure the heat-sink

retention module to the system board; then, lift the heat-sink retention module
from the system board.

10. If you are instructed to return the heat-sink retention module, follow all

packaging instructions, and use any packaging materials for shipping that are
supplied to you.

292

IBM System x3400 M3 Types 7378 and 7379: Problem Determination and Service Guide

Содержание 7378











































































































































































































































































































































































Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды

IBM 7378, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды