IBM 7378 Скачать руководство пользователя страница 301

Страница: 301 / 362

Installing an extender card

To install an extender card, complete the following steps:

1. Touch the static-protective package that contains the extender card to any

unpainted metal surface on the server; then, remove the extender card from the
package.

2. Align the extender card with its connector on the system board; then, slide the

extender card into the connector.

3. Install the two screws that secure the extender card to the system board tray.

4. Install the system board in the server (see “Installing the system board” on page

298).

5. Install any adapters that you removed from the expansion slots (see “Installing

an adapter” on page 215).

6. Install and lock the left-side cover (see “Installing the left-side cover” on page

181).

7. Reconnect the external cables and power cords; then, turn on the attached

devices and turn on the server.

Chapter 5. Removing and replacing server components

283

Содержание 7378











































































































































































































































































































































































Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды

IBM 7378, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды