IBM 7378 Скачать руководство пользователя страница 288

Страница: 288 / 362

Installing the upper 3.5-inch disk drive cage

To install a 3.5-inch hard disk drive cage, complete the following steps:

1. Remove all the EMC fillers.

2. Remove the optical DVD drive if installed.

3. Remove the EMC shields and store them for future use.

4. Touch the static-protective package that contains the 3.5-inch disk drive cage

to any unpainted metal surface on the server; then, remove the drive cage
from the package.

5. Install the UltraSlim DVD drive in to the slim slot on top of the upper 3.5-inch

disk drive cage; follow steps from 2 on page 206 to 2o on page 210.

6. Install the 3.5-inch disk drive backplane in the back of the drive cage (see

“Installing the 3.5-inch hard disk drive backplane” on page 259).

7. Slide the 3.5-inch disk drive cage into the upper opening of the server along

the lower edge of the opening.

Note:

Pull the power and signal cables of the UltraSlim DVD drive into the

upper opening of the server first. Make sure the cables are not stuck when you
slide the disk drive cage into the server.

270

IBM System x3400 M3 Types 7378 and 7379: Problem Determination and Service Guide

Содержание 7378











































































































































































































































































































































































Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды

IBM 7378, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды