manualshive.com logo in svg

IBM 3401-A00, Руководство по эксплуатации прибора

Поделиться
Скачать
IBM 3401-A00 Скачать руководство пользователя страница 35

Chapter 5. Field replaceable units

A number of components can be replaced in the field.

Replacement parts

Contact IBM Support for replacement parts for this appliance.

The following customer serviceable parts are available:

v

PSU, RPS, 750 W, 110 - 240 VAC, 12 VDC, FPS

v

2.5" OS drives

The following customer serviceable upgrades are available:

v

SFP+/QSFP optical modules

See the Field Replaceable Units Reference Guide for a complete list of available drives.

Replace external front components

Replace the operating system drive

1.

Log in to the device as 

localadmin

.

2.

At the command prompt, type 

poweroff

. After the appliance is powered off, you can remove the

power cord and network cables from the back of the chassis.

3.

Locate the drive by location label or failure LED.

4.

Press the release button on the drive carrier. This action extends the carrier handle, as shown in the
following figure.

5.

Pull the drive carrier out of the chassis by using the handle.

6.

Make sure that the drive carrier latch on new drive is open.

7.

Push the drive carrier with the new HDD into the chassis until significant resistance is encountered.

8.

Reclose the latch to fully seat the drive carrier into the chassis.

Figure 17. Removing a drive from the chassis

© Copyright IBM Corp. 2016, .

17

Содержание 3401-A00













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды