v
A:
is the drive letter of the diskette drive.
v
/F
forces the diskette to be reformatted.
To create the IBM Token Ring Diagnostic diskette the command would be:
F:\DIAG\LOADDSKF F:\DIAG\IBMTR\IBMTRDGS.DSK A: /F
3. Label the diskette with the diagnostic name that is on it.
Configuration Save/Restore Procedures
CFGSR saves or restores parts of the OS/2 configuration to diskette. The purpose
is to restore the configuration when OS/2 needs to be re-installed because of a disk
failure that affects the hard drive, or when a new software level is installed that
requires OS/2 to be reinstalled from CD.
When to use CFGSR:
1. After a new install to save the 2074 initial customer configuration.
2. After changing the 2074 device configuration (e.g. Configure CA 0 or 1 icons),
PC 3270 session defaults, or TCP/IP addresses.
3. Before the IBM CE reloads the hard disk from the 2074 Load CD to solve a
program problem or exchange the hard disk for analysis.
4. After reloading the hard disk to restore the previous configuration.
CFGSR saves specific data from the C: and E: drives, such as CONFIG.SYS, PC
3270 customization, DEVMAPs, TCP/IP customization such as IP addresses, etc. It
does not save the desktop configuration (folders, etc.) if modified from the 2074
defaults. The customer will have to recreate any folders or icons that he has added
to the OS/2 desktop.
Configuration Save/Restore Steps
Save Configuration data
1. Insert a blank, formatted 1.44MB diskette into the diskette drive.
2. From the OS/2 desktop, Double-click on the ’2074 Utilities’ Icon.
3. Double-click on the ’SAVE/RESTORE Customer Configuration’ Icon within the
’2074 Utilities’ folder.
4. Type
SAVE
at the prompt that appears and press
ENTER
.
5. When you see the message
Configuration backup complete
remove the
diskette and set the write protect tab to the open position. Be sure to label and
date the diskette.
Restore Configuration data
1. Insert the configuration backup diskette in the diskette drive.
2. From the OS/2 desktop, Double-click on the ’2074 Utilities’ Icon.
3. Double-click on the ’SAVE/RESTORE Customer Configuration’ Icon within the
’2074 Utilities’ folder.
4. Type
RESTORE
at the prompt that appears and press
ENTER
.
5. After restoring a configuration, be sure to
reboot the system
so the restored
files become active.
Notes:
1. A confirmation message will be displayed before any existing files will be
overlaid.
Chapter 3. Service Procedures
3-11
|
|
|
|
Содержание 2074
