manualshive.com logo in svg

ibidi 11920, Инструкция по эксплуатации

Поделиться
Скачать
ibidi 11920 Скачать руководство пользователя страница 11

Gas Incubation System

• Only ibidi technical staff and technical staff instructed by ibidi are permitted to open and ser-

vice the Gas Incubation System.

• The external power supply should not be brought into contact with moisture. If the housing is

damaged, the external power supply should not be used.

• Avoid strong magnetic fields and sources of high frequency. The Gas Incubation System might

not function properly when located near a strong magnetic field or high frequency source.

• Avoid vibrations from vacuum pumps, centrifuges, electric motors, processing equipment, and

machine tools.

• Avoid dust and corrosive gas. Do not install the Gas Incubation System where it could be

exposed to high levels of dust or to outside air or ventilation outlets.

• Install the Gas Incubation System in a horizontal and stable position, such as a table, bench, or

desk upon which the instrument is installed.

• Install the Gas Incubation System in a location that enables easy access for maintenance.

• Do not place heavy objects on the instrument.

• The Gas Mixer needs a gas input of 1 bar/14.5 psi. Only operate the Gas Mixer with the pressure

indicated in the specifications on page

7

.

1.7

Regulatory Statement

The Gas Incubation System has been designed, produced and tested in compliance with the European
standard DIN EN 61010-1 (IEC 61010-1, ”Safety requirements for electrical equipment for measure-
ment, control and laboratory use”). Furthermore it meets the IEC 61326-1 (”Electrical equipment
for measurement, control and laboratory use - EMC requirements”) and CISPR 11 (”International
Standard for electromagnetic emissions (disturbances) from Industrial, Scientific and Medical (ISM)
Equipment”) standards .

The device carries the CE mark.

The Gas Incubation System meets the Low Voltage Directive 2014/35/EU and the
EMC Directive 2014/30/EC.

Instruction Manual

11

Version 2.2 (May 15, 2019)

Содержание 11920





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды