manualshive.com logo in svg

ibidi 10929, Инструкция по эксплуатации

Поделиться
Скачать
ibidi 10929 Скачать руководство пользователя страница 22

ibidi Heating System, Multi-Well Plates, K-Frame

Mode

Each channel of the Temperature Controller can be set to an ”On” or ”Off” state. For standard

operation all channels must be turned on.

<Mode>

Setup

Channel = 1

Mode    = On

Return

Figure 12 – Mode dialog

1. Press the round button once more to move the cursor to the channel number.

2. Select the respective channel and confirm with the round button.

3. Select ”On” or ”Off” and confirm with the round button.

4. To move on navigate to ”Return” and press the round button.

Alarms

In this dialog it is possible to set the alarm limits for divergent control parameters. Move

from the mode menu to the alarm menu by pressing the ”right” button.

The maximum and minimum limits of the alarm can be set for each individual channel. If the alarm is
activated (which happens when the current value goes under/over the low/high limits), the current
value (I) blinks, showing alternately the value and ”low” or ”high”, respectively. To stop the display
blinking, navigate to the blinking channel and press the round button once.

<Alarms>

Setup

Channel = 4

High    = 42°C

Low     = 36°C

Figure 13 – Alarm settings dialog

Preferences

Set the brightness and contrast of the display in the preferences menu.

<Preferences>

Setup

Backlight = 65

Contrast  = 15

Return

Figure 14 – Preferences dialog

Info

Info about serial number and firmware version is shown in the info dialog.

Figure 15 – Info display

Version 2.0 (March 22, 2019)

22

Instruction Manual

Содержание 10929





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды