Parts
a Rim hook
b Allen bolts, washers x 2
c Front wheel bracket
d Rear wheel rest
e Wall plugs (screw anchors) x 5
(for masonry or concrete walls only)
f Screws x 5
Tools Required
4 mm Allen key
Drill
Drill bit
Phillips head screwdriver
Hammer (if wall plugs are used)
INSTRUCTIONS
Mark 3 drill holes: left, right and lower hole–do not use the top
centre hole (fig. 4b). Drill holes with a 6.5 mm (1/4") drill bit.
Install 3 wall plugs with hammer after drilling holes, making
sure they are firmly pressed in. Fasten bracket firmly with
screws (fig. 4c).
If tyre recess is not already facing towards the right, press
release lever and swing rightwards until it locks in with a 'click.'
With Allen bolt and washers, assemble rim hook to tyre recess
(hook faces right). Tighten well (fig. 1, fig. 2).
Mount Front Wheel Bracket
Mount hanger on a solid wall, or along wall stud (upright timber)
of a plasterboard wall (drywall). Mount in a place where it is
unlikely to cause obstruction, be knocked or bumped, or
interfered with by young children. Determine correct height for
hanger (rear tyre should sit at least 5 cm (2") off floor or ground),
and make sure it is in a straight vertical position (fig. 3).
Hanger must be mounted securely on a wall stud (one of the
vertical lengths of timber behind the wall). Use a stud finder to
locate stud, and mark its centreline with a pencil. Place the
bracket on wall with stud centreline between the centre hole
and right hole–do not use the left hole (fig. 4b). Mark 3 drill
holes: centre, right and lower hole. Drill holes. Fasten bracket
firmly with screws (fig. 4a).
fig. 4c
fig. 1
fig. 3
For Mounting on Drywall (plasterboard), or
Wooden Panel Walls
Warning
• Do not mount hanger on drywall, or wooden panel walls unless there is a wooden stud behind it.
• Use drill bit of appropriate size and type: e.g. masonry drill bit for masonry.
• Avoid any electrical, plumbing, or water fittings hidden in or behind walls.
• Mount in a place where it is unlikely to cause obstruction, be knocked or bumped, or interfered with by young children.
• If you lack the DIY skills to install hanger, seek professional help.
警告(繁體中文)
1
、請勿將本產品鎖固在沒有支撐的牆壁、石膏板或裝飾板上。
2
、磚塊或水泥牆請使用
6.5mm
的鑽頭鑽孔。
3
、安裝時請避開電子電路，
瓦斯、天然氣或自來水的管線。
4
、吊掛自行車前，請確認本產品有確實地安裝在實心柱子、樑或牆上，以避免對人和自行車造成損傷。
5
、如果您缺乏
DIY
技
能安裝，請尋求專業幫助。
警告(简体中文)
1
、请勿将本产品锁固在没有支撑的墙壁、石膏板或装饰板上。
2
、砖块或水泥墙请使用
6.5mm
的钻头钻孔。
3
、安装时请避开电子电路，
瓦斯、天然气或自来水的管线。
4
、吊挂自行车前，请确认本产品有确实地安装在实心柱子、梁或墙上，以避免对人和自行车造成损伤。
5
、如果您缺乏
DIY
技
能安装，请寻求专业帮助。
www
.ibera.info
USER MANUAL
Side Swing Bicycle Hanger
Side Swing Bicycle Hanger
For mounting a bike vertically on wall.
Mount Hanger
Mount Hanger
Assemble Hanger
Assemble Hanger
Max. Load 18 kg / 40 lb. (
最大載重
18 kg)
b
c
d
e
f
a
Compatibility
Wheel size: 20"–29".
Tyre Size–Max. height (rim+tyre): 8 cm (3.15”);
Max. width: 7.62 cm (3").
Max. 8 cm
Max. 7.62 cm
Drill holes
(6.5 mm diameter)
Wall
Rim hook
Min 5 cm (2")
fig. 2
Left
Right
fig. 4a
石膏板或木板的支撐柱
Bracket
Drill holes
Release lever
Left & right locking points
(underside view)
Rear wheel
rest
Tyre recess
For Mounting on Masonry or
Concrete Walls
磚塊或水泥墻
Left hole
Centre hole
Right hole
fig. 4b
