IBC CX Series Скачать руководство пользователя страница 78

Страница: 78 / 124

To perform a fuel conversion:

Removing the mixer

1. Turn off the gas supply.

2. Change the gas fuel source.

3. Before you disconnect the electrical power, shut off the gas supply at the gas shut-off

valve.

4. Disconnect the electrical power.

5. Remove the front door cover.

6. Undo the brass union nut between the gas valve outlet pipe and the mixer. Set the gasket

aside for re-installation.

7. Note the orientation and the positions of the mixer's Philips head bolts.

8. Remove the bolts and the mixer from the fan.

9. Ensure that the fan O-Ring is not damaged and is seated in the groove.

Installing the new mixer

1. Install the new fuel-appropriate mixer with the Philips head bolts.

2. Check that the gasket is in place between the gas valve outlet pipe and the mixer.

3. Connect the gas line to the mixer using the brass union nut.

4. Restore the gas supply by opening the gas control valve and reconnect the electrical

power.

5. Perform a combustion test (see instructions below).

6. When the boiler is running, use an approved leak detection solution to soap test all joints.

7. Place conversion labels associated with the new fuel onto the boiler.

6.3.3 Adjusting the gas valve

Danger

Making adjustments to the IBC gas valve without a properly calibrated gas
combustion analyzer and by persons who are not trained and experienced in its use
is forbidden. Failure to use an analyzer can result in an immediate hazard.

Section: Boiler operation

Содержание CX Series





























































































































Результаты поиска

Содержание CX Series

Отзывы:

IBC CX Series, Инструкция по установке и эксплуатации, Страница: 78 / 124

Результаты поиска

Содержание CX Series

Отзывы: