IBC CX Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 124

IBC CX Series Скачать руководство пользователя страница 7

Safety information

Manual safety markings

Danger

Points out an immediate hazardous
situation that must be avoided to
prevent serious injury or death.

Warning

Points out a potential hazardous
situation that must be avoided to
prevent serious injury or death.

Caution

Points out a potential hazardous
situation that must be avoided to
prevent possible moderate injury
and/or property damage.

Note

Points out installation, maintenance and
operational notes to enhance efficiency,
longevity and proper operation of the
boiler.

Important safety instructions

Installation, start-up and servicing of IBC boilers must be performed by competent, qualified, licensed
and trained heating technicians.

Failure to read and comply with all instructions and applicable national and local codes may result in
hazardous conditions that could result in property damage and injury to occupants, and in extreme
cases to death. Keep instructions near the air handling appliance for future reference.

7

Safety information

«
...
5
6
7
8
9
...
»

Содержание CX Series





























































































































Отзывы:

Нет отзывов