i3 International S81 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 205

background image

178

LLDP EEE Parameters:

Items

Description

Local Port

The port for this switch on which the LLDP frames are received or transmitted.

Tx TW

The link partner’s maximum time that transmit path can hold off sending data after reassertion
of LPI.

Rx TW

The link partner’s time that receiver would like the transmitter to hold off to allow time for the
receiver to wake from sleep.

Fallback Receive Tw

The link partner’s fallback receive Tw. A receiving link partner may inform the transmitter of an
alternate desired Tw sys Tx. Since a receiving link partner is likely to have discrete levels for
savings, this provides the transmitter with additional information that it may use for a more
efficient allocation. Systems that do not implement this option default the value to be the
same as that of the Receive Tw_sys_Tx.

Echo Tx Tw

The respective echo values shall be defined as the local link partner’s reflection (echo) of the
remote link partners respective values. When a local link partner receives its echoed values
from the remote link partner it can determine whether or not the remote link partner has
received, registered and processed its most recent values. For example, if the local link partner
receives echoed parameters that do not match the values in its local MIB, then the local link
partner infers that the remote link partners request was based on stale information.

Echo Rx Tw

The link partner's Echo Rx Tw value.

Resolved Tx Tw

The resolved Tx Tw for this link. This is not the link partner. The resolved value that is the actual
"tx wakeup time” used for this link (based on EEE information exchanged via LLDP).

Resolved Rx Tw

The resolved Rx Tw for this link. This is not the link partner. The resolved value that is the
actual "tx wakeup time” used for this link (based on EEE information exchanged via LLDP).

EEE om Sync

Displays whether the switch and the link partner have agreed on wake times.
Red - Switch and link partner have not agreed on wakeup times.
Green – Switch and link partner have agreed on wakeup times.

Buttons

Auto-refresh: Check this box to refresh the page automatically. Automatic refresh occurs
every 3 seconds.
Refresh: Click to manually refresh the page.

LLDP Port Statistics

Two types of counters are displayed. Global counters are counters that refer to the entire switch, while local counters refer
to port counters for the currently selected port.
To display the Port Statistics in the web interface:



Click Monitor / LLDP / Port Statistics



Check the Auto-Refresh check box to have the page automatically refresh every 3 seconds.

«
...
177
178
179
180
181
...
»

Содержание S81














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S81

Бренд: Fantech Страницы: 4

Бренд: Ruby Tech Страницы: 2

Бренд: Touch-plate Страницы: 12

Бренд: NBase Communications Страницы: 72

MCD-LED17 series

Бренд: Raritan Страницы: 89

Бренд: Avenview Страницы: 10

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

Бренд: Black Box Страницы: 20

LiteWave LS105G

Бренд: TP-Link Страницы: 3

Бренд: AT&T Страницы: 24

Бренд: Wyrestorm Страницы: 2

Бренд: WilTec Страницы: 7

Бренд: Versa Technology Страницы: 96

Бренд: CONCORD Страницы: 18

Бренд: SMART-AVI Страницы: 2

Бренд: IDK Страницы: 81

Бренд: I-Rocks Страницы: 23

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды