User Manual
UP
4
140mm (
5½
”)
Ø147mm (
5¾
”)
Ø99.94mm (3.93”)
5
6
8
9
10
11
12
13
1
1
2
7
CVBS
WDR
CVBS
2MP Outdoor IR HD Analog Dome w/ Motorized Lens
Am57
Thank you for purchasing i3 International’s Am57 High Definition indoor/
outdoor analog dome camera. Your camera is equipped with a motorized vari-
focal 2.8-12mm @ F1.2 lens. The lens can be controlled through cameras’
built-in OSD menu via SRX-Pro Server/VPC, or through i3 encoders and
standalone HVRs (Veo16p).
SAFETY
When installing your Am57 camera be sure to avoid:
•
excessive heat, such as direct sunlight or heating appliances
•
contaminants such as dust and smoke
•
strong magnetic fields
•
moisture and humidity
•
areas with mechanical vibrations
•
fluorescent lamps or objects that reflect light and unstable light sources
•
temperatures below -40°C (-40°F) and above 60°C (140°F)
CLEANING & SERVICING
For maximum optical clarity, the camera dome or lens must remain clean.
Use a soft, dry cloth to remove finger prints or dust from the dome cover.
•
Use a blower to remove dust from the lens.
•
Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
•
To avoid electrical shock and to preserve the product warranty, DO NOT
disassemble the camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the
packing slip. In addition to this manual and a fully assembled camera, the dome
camera packing box includes:
A.
Surface Mount template x1
B.
Isolated power adapter x1
C.
Service monitor cable x1
D.
Security Torx bit x1
E.
Plastic Anchor x3
F.
Round Head Screw (Tapping Type) x3
G.
Waterproof tape x3
E
A
B
Waterproof tape
e Waterproof tape
pe Waterproof ta
f tape Waterproo
oof tape Waterpr
proof tape Water
C
D
HIGH DEFINITION ANALOG VIDEO SUPPORT
Your Am57 camera supports both the standard composite analog video stream
(CVBS, 720x480) and a high-definition TVI video stream (HD-TVI = 2MP). Both
streams are supported simultaneously as long as the on-board dip switch is set to
CVBS position.
IMPORTANT:
In order to use high-definition video,
your Am57 camera must
be connected to i3’s video encoder or standalone DVR
. To record camera’s
HD-TVI stream (2MP) to SRX-Pro Server, connect the camera’s gray BNC cable
connector (labeled 2MP) to i3’s encoder or standalone DVR. If connecting directly
to the HVR’s BNC panel, use the black BNC cable connector (720x480).
SERVICE MONITOR OUTPUT
To use the service monitor to adjust zoom and focus for the motorized varifocal
lens during installation, use the 2-pin connector on the camera board to connect
the service monitor. Set the WDR/CVBS dip-switch to
CVBS
(True WDR will be
disabled). If using HD-TVI video output, make sure to return the dip-switch to WDR
position before completing the installation.
CVBS SPOT MONITOR OUTPUT
To use the CVBS stream for the spot monitor output, set the WDR/CVBS dip-switch
to
CVBS
, then connect the camera’s black BNC cable (labeled 720x480) directly to
the spot monitor.
Note:
True WDR and OSD menu are not available in CVBS mode.
Lens Direction
GUIDE PATTERN
F
DIMENSIONS AND DEFINITIONS
G
Rev. 221109
1.
Long screws (pre-installed) for attaching camera module to the back box
(x3, silver. Use provided security torx bit).
2.
Motorized 2.7-13.5mm lens. See LENS ADJUSTMENT section for more
information.
3.
IR board.
4.
CVBS standard-format analog video connector (4CIF = 720x480). Can
be connected directly to the BNC board on the i3’s HVR units or to a spot
monitor.
5.
TVI High-definition analog video connector (2MP. 1920x1080 = 1080P).
To use high-definition analog stream (2MP), the camera must be
connected to i3’s encoder or standalone DVR.
6.
Power connector (DC12V / AC24V). Connect Isolated
7.
Not in use.
8.
Screws attaching camera bubble to the camera module (x3, silver. Use
provided security torx bit).
9.
Dome bubble.
10.
Camera’s back box. Compatible with i3’s DB60 Goose-neck bracket. Can
also be used for pendant mount installations.
11.
Side conduit hole (3/4”).
Remove plug to route power and video cables through the side opening.
Use the plug for the top conduit hole in that scenario.
When using outdoors, sealant must be used to maintain the IP67 status.
12.
Top conduit hole (3/4”). Can also be used for pendant mount installations.
When using outdoors, sealant must be used to maintain the IP67 status.
13.
Mounting holes, partially drilled, x6 (complete drilling the holes prior to
installation).
ACT Download &
Documentation
for
Annexxus Configuration Tool (ACT)
installation and additional documentation.
Contact our Technical Support team at:
1.877.877.7241
or
if you have any questions or concerns
regarding camera installation or if you require
software services or support.
