User Manual
i3-TRNG-CAMS-
Am52RM-UM
.indd
Rev.
180216
安装贴纸
DB60 -
Goose-neck
Bracket
Am42R -
Back box
Use silicone
to maintain
IP66 rating
Use silicone
to maintain
IP66 rating
3/4” Electrical
EMT Conduit
Fitting
Ridgid
3/4” pipe
Am42R -
Back box
CVBS
WDR
2MP
720x480
UP
1080P (2MP) Infrared Outdoor HD Analog Dome w/ Motorized Lens
Am52RM
Thank you for purchasing i3 International’s
Am52RM High Definition indoor/outdoor
analog dome camera. Your camera is equipped with a motorized vari-focal 2.8-12mm @
F1.4 lens. The lens can be controlled through the camera’s built-in OSD menu, through IE
interface of the i3 encoders/standalone DVRs, or through SRX-Pro Server.
SAFETY
When installing your Am52RM camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -30° C (-22° F) and above 60° C (140° F)
.
POWER
This camera accepts DC12V and AC24V power. Maximum power consumption: 6W.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING & SERVICING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
• To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
1. Plastic Anchor x4
2. Round Head Screw
(Tapping Type) x4
3. Security Torx bit x1
4. Spot monitor auxiliary
video output cable x1
5. Surface Mount template x1
1.
3-axis camera module / second housing.
2.
Long screws (pre-installed) for attaching camera module to the back box (x3,
silver. Use provided security torx bit).
3.
Motorized 2.8-12mm lens. See LENS ADJUSTMENT section for more information.
4.
IR board.
5.
Joystick (for on-screen camera menu control)
6.
Dip switch (CVBS / WDR). Remove the Shroud/Liner for easy access. When the
switch is set to CVBS, the Service Monitor and CVBS output is enabled and True
WDR is disabled. When the switch is set to WDR, the Service Monitor and CVBS
output is disabled but True WDR is enabled.
7.
2-pin Service monitor output. Use to adjust and focus the motorized varifocal lens
during installation. Set the dipswitch to CVBS mode to use.
8.
Power connector (DC12V / AC24V).
9.
TVI High-definition analog video connector (2MP. 1920x1080 = 1080P).
To use high-definition analog stream (2MP), the camera must be connected to i3’s
encoder or standalone DVR.
10.
CVBS standard-format analog video connector (4CIF = 720x480). Can be
connected directly to the BNC board on the i3’s HVR units or to a spot monitor.
11.
Lexan Bubble (Dome).
12.
Screws attaching camera bubble to the camera module (x3, silver. Use provided
security torx bit).
13.
Inner liner / Shroud (Removable for convenient lens position adjustments).
14.
Camera’s back box.
Compatible with i3’s DB60 Goose-neck bracket. Can also be used for pendant
mount installations.
15.
Side conduit hole (3/4”).
Remove plug to route power and video cables through the side opening.
Use the plug for the top conduit hole in that scenario.
When using outdoors, sealant must be used to maintain the IP66 status.
16.
Top conduit hole (3/4”). Can also be used for pendant mount installations.
When using outdoors, sealant must be used to maintain the IP66 status.
17.
Mounting holes, partially drilled, x6 (complete drilling the holes prior to
installation).
CAMERA PARTS AND DEFINITIONS
1
Lens Direction
GUIDE PATTERN
HIGH-DEFINITION ANALOG VIDEO SUPPORT
Your Am52RM camera supports both the standard composite analog video stream
(720x480) and a high-definition TVI video stream (HD-TVI = 2MP). Both streams are
supported simultaneously as long as the on-board dip switch is set to CVBS position.
IMPORTANT:
In order to use high-definition video, your Am52RM camera
must be
connected to i3’s video encoder
or standalone DVR.
To record camera’s HD-TVI
stream (2MP) to SRX-Pro Server, connect the camera’s gray BNC cable connector (labeled
2MP) to i3’s encoder or standalone DVR. If connecting directly to the HVR’s BNC panel, use
720x480 composite video cable
.
SERVICE MONITOR OUTPUT
To use the service monitor to adjust zoom and focus for the motorized varifocal lens during
installation, use the 2-pin connector on the camera board to connect the service monitor.
The WDR/CVBS dip-switch must be set to CVBS (True WDR will be disabled). If using HD-
TVI video output, make sure to return the dip-switch to WDR position before completing
the installation.
CVBS SPOT MONITOR OUTPUT
To use the CVBS stream for the spot monitor output, connect the camera’s black BNC
cable (labeled 720x480) directly to the spot monitor. The WDR/CVBS dip-switch must be
set to CVBS. True WDR will be disabled.
3
8
9
10
5
6
7
11
13
14
17
15
16
12
4
1
2
2
2
3
4
5
