Ns0522-0
Printed in China
Ceiling Mount Bracket
Model No.
WV-QCD100
Operating Instructions
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
Preface
About notations
This product is a ceiling mount bracket that is designed to mount the indoor PTZ type camera on a
ceiling.
The latest information about the supported cameras
<Control No.: C0501>
Some functions are expressed with the following notations in this document.
C
Clear dome cover
G
Smoke dome cover
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety
wire.
When using this product, also read the “Precautions” described in the operating
instructions for the camera to be attached.
Precautions
Installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation .
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
Notice:
• This product is not suitable for use in loca-
tions where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
Included Installation Instructions
Specifications
In order to prevent injury, the product must be securely mounted to the camera
according to the Installation Guide of this product.
This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
Make sure to remove this product if it will no longer be used.
Precautions for installation
Standard Accessories
Refer to the operating instructions of the camera for details on the camera installation
(including the camera mounting, cable connection and adjustment).
Ambient temperature:
–10 °C to +50 °C {14 °F to 122 °F}
Dimensions:
Maximum diameter ø185 mm × 163 mm (H)
{ø7-9/32 inches × 6-13/32 inches (H)}
Mass:
Approx. 230
g
{0.51 lbs.}
Finish:
Main body:
ABS resin i-PRO white
Dome cover:
Acrylic resin
C
G
(Transmittance: approx. 50 %)
“<Control No.: C****>” used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
© i-PRO Co., Ltd. 2022
i-PRO Co., Ltd.
https://www.i-pro.com/
LOCK
OPEN
Operating Instructions (this document) ............1 pc.
The following are for installation.
Inner cover (WV-QAT100) ...............................1 pc.
Parts and functions
Side cable access hole
Dome cover
Main body
Hole for microphone cable
Rubber-made
microphone stand*
* If a tiepin type microphone is used, mount the microphone on the rubber-made microphone
stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
IMPORTANT:
• To prevent injuries and protect the cables, finish the side cable access hole with a file to avoid
sharp edges.
③
Turn this product clockwise until the projection of the camera mounting bracket aligns with
“LOCK” of this product.
LOCK
OPEN
Safety wire
Safety wire hook
Projection of camera mounting bracket
LOCK
OPEN
LOCK
OPEN
LOCK
OPEN
②
Mount this product on the camera with aligning
the projection of the camera mounting bracket
(2 places) with “OPEN” of this product (2 places).
Note:
• Make sure to face the product in a direc-
tion its i-PRO logo aligns with the one on
the camera.
IMPORTANT:
• Use caution not to catch the cables.
①
Connect the safety wire attached on this product
to the safety wire hook.
Make sure that the apical ring of the safety wire is
engaged with the safety wire hook of the camera
mounting bracket by pulling the safety wire after
connection.
Note:
• When the tilt angle of the camera is almost level, the upper side of images will be hidden by this
product reflecting on the screen. In such a case, adjust the tilt angle. Refer to the Operating
Instructions of the camera for further information.
Projection of the camera
mount bracket
The camera shall be mounted on the camera mounting bracket (supplied with the camera) after
mounting it on a ceiling.
For further information, refer to the Installation Guide of the camera.
LOCK
OPEN
LOCK
OPEN
Step 2
Step 3
Step 1
Attach the inner cover.
Mount the camera.
Install this product to the camera mounting bracket.
Step 4
Remove the protection sheet from the dome cover.
②
Attach the inner cover.
When removing the inner cover
Release the claws on the inner surface on both the left and right sides one by one and
then remove the inner cover.
①
Remove the side covers from the camera main body. (Both the left and right sides)
Click feeling
A click sound
is heard.
Claws on the
inner surface
